manualshive.com logo in svg

ROBBE-Futaba FX-32, Instruction Manual

Share
Download
ROBBE-Futaba FX-32 Instruction Manual Download Page 30

30

<Before Use>

Telemetry System

The R7008SB receiver features bi-directional communication with a FASSTest Futaba transmitter using 

the S.BUS2 port.  Using the S.BUS2 port an impressive array of telemetry sensors may be utilized.  It also 

includes both standard PWM output ports and S.BUS output ports.
*Telemetry is available only in the FASSTest 18CH mode. (12CH mode displays only receiver battery 

voltage and extra battery voltage.)

*The telemetry function requires the corresponding receiver (R7008SB).
* Telemetry display only FX-32 ID of  R7008SB was remembered to be.

S.BUS2

connector

Temperature

Sensor

Slot 1

Slot 2

Slot 3 〜 5

Slot 6 〜 7

Slot 8 〜 15

Slot 16

Receiver

Battery voltage is 

displayed at the transmitter.

Power battery voltage is 

displayed at the transmitter.

Switch

FX-32

Terminal box

Hub

Hub

Hub

Info

Info

Info

Info

Info

Voltage

Signal

RPM

Sensor

Altitude

Sensor

GPS

Sensor

Voltage

Sensor

Slot 17

Slot 31

***Sensor

***Sensor

●Telemetry sensor (sold separately)

Your aircrafts data can be checked in the 

transmitter by connecting various telemetry 

sensors to the S.BUS2 connector of the 

receiver.

●Slot No.

 

Servos are classified by channel, but sensors 

are classified by “slot” . Since the initial slot 

No. of the FX-32 is preset at each sensor, the 

sensors can be used as is by connecting 

them. There are 1

~

31 slots.

Info

Telemetry 

Data

Summary of Contents for FX-32





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands