ROBBE-Futaba FX-32 Instruction Manual Download Page 164

Page: 164 / 180

164

<Functions of Model Menu (Helicopter Functions)>

● S e l e c t t h e f u n c t i o n

name and return to the

p r e c e d i n g s c r e e n b y

touching the

RTN

button

or pushing the

Home/Exit

button.

<SensorTouch™>

GOVERNOR mixing

When using a Futaba governor, this function is

used to switch the RPM of the helicopters head. Up

to 3 rates can be set for each condition.

*The governor is used by connecting the governor speed

setting channel to CH7 (initial setting).

*When using an independent governor [ON]/[OFF] switch,

connect the AUX([ON]/[OFF]) connector of the governor to

CH8 (initial setting) and set the switch to CH8 (Governor2)

at the Function menu of the Linkage Menu.

*When using the Fuel Mixture function, the mixture servo

is controlled from the governor. When transmitting the

mixture curve data from the transmitter to the governor, the

governor AUX (m.trm) connector must be connected to CH8

(initial setting) and governor side setting performed. See the

governor instruction manual.

Note: Always set (Control) and (Trim) to [--] for

[Governor] and [Governor 2] of the Function menu

of the Linkage menu.

● Select [GOVERNOR] at the model

menu and call the setup screen shown

below by touching the RTN button.

(Currently selected condition name)

●Fine tuning VR settings

●RPM adjustment

●Unit display selection:
[%]/[rpm]

Setting method

●Activate the mixing

When using this function, move the cursor to

the [INH] item and touch the RTN button to

switch to the data input mode.

Select the ACT mode by scrolling the touch

sensor.

*The display blinks.

Touch the RTN button to activate the mixing

and return to the cursor mode. (ON is

displayed.)

When the Governor is changed from the

default inhibited (INH) state to the active

(ACT) state, the endpoint menu will be

displayed and it is possible to utilize the

endpoints for this given condition.

*When the function is set ON/OFF at the governor setup

screen, the governor rpm setting channel end point servo

travel and limit point are now initialized.

*When changed from INH to ACT (ON), the servo travel is

initialized to 100 and the limit point is initialized to 155.

*When operation is changed to INH at all conditions, the

servo travel is initialized to 100 and the limit point is

initialized to 135.

●RPM adjustment

Move the cursor to the rate item and touch

the RTN button to switch to the data input

mode.

Adjust the rpm by scrolling the touch sensor.

Initial value: 50% (1500rpm)

Adjustment range: OFF, 0~110% (OFF,

700~3500rpm)

*When the RTN button is touched for one second, the

sensitivity is reset to the initial value.)

Touch the RTN button to return to the cursor

mode.

●Unit diplay selection

Move the cursor to the UNIT item and touch

the RTN button to switch to the data input

mode. Select the unit by scrolling the touch

sensor.

Touch the RTN button to change the

operation mode and return to the cursor

mode.

Scrolling

● Moving cursor

● Selecting mode

● Adjusting value

● To next page

Summary of Contents for FX-32





















































































































































































Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands

ROBBE-Futaba FX-32, Instruction Manual

Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands