manualshive.com logo in svg

ROBBE-Futaba FX-32, Instruction Manual

Share
Download
ROBBE-Futaba FX-32 Instruction Manual Download Page 43

43

<Functions of System Menu>

● Select the function name 

and return to the System 

menu  by  touching  the 

RTN button or pushing the 

Home/Exit button.

<SensorTouch™>

3 independent sound volumes: "WARNING", 

"VOICE" and others, are available.

"LOW BATTERY" adjusts low battery alarm 

voltage to match a battery.

● Select [SOUND] at the system menu and access 

the setup screen shown below by touching the 

RTN button.

● LOW BATTERY : 6.8V~7.6V

Sound volume operation

1. Move the cursor to the [WARNING][VOICE] 

or [OTHER SOUND] item and touch the RTN 

button to switch to the data input mode.

2. Select  the  volume  by  scrolling  the  touch 

sensor. 

*The display blinks.

3.Touch the RTN button.

Low battery voltage operation

1. Move the cursor to the [LOW BATTERY] item 

and touch the RTN button to voltage to the 

data input mode.

2. Select  the  voltage  by  scrolling  the  touch 

sensor. (6.8V-7.6V)

*The display blinks.

3.Touch the RTN button.

SOUND

Turns off the buzzer.

Scrolling

● Moving cursor

● Adjusting value

Summary of Contents for FX-32





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands