ROBBE-Futaba FX-32 Instruction Manual Download Page 165

Page: 165 / 180

165

<Functions of Model Menu (Helicopter Functions)>

●Diplay mode selection

*When [rpm] mode is selected above setting, the display

mode can be selected.

* There is no change in the transmitter output even when the

"MODE" is changed. Calibration should be performed via

the governor.

* In order to use the Governor function of the FX-32, it is

necessary to change the settings on the governor for the low

side 700 rpm mode.

When the MODE of the Governor screen's

model menu is changed, the change is also

indicated on-screen.

The chart below indicates the

m o d e p e r c e n t a g e a n d t h e

corresponding RPM.

●Fine tuning VR settings

Move the cursor to the [--] item and touch

the RTN button to access the selection

screen. Select the control.

*For a description of the switch selection method, see the

description at the back of this manual.

Move the cursor to the rate item and touch

the RTN button to switch to the data input

mode.

Adjust the trim rate by scrolling the touch

sensor.

Initial value: 0% (0rpm)
Adjustment range: -20~+20% (-800~+800rpm)

*When the RTN button is touched for one second, the

sensitivity is reset to the initial value.)

Touch the RTN button to return to the cursor

mode.

main rotor R.P.M.

3900rpm

2700rpm

2100rpm

100% 110%

main rotor R.P.M. setting channel travel

50% : neutral

2500rpm

2000rpm

1500rpm

1000rpm

700rpm

3500rpm

Summary of Contents for FX-32





















































































































































































Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands

ROBBE-Futaba FX-32, Instruction Manual

Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands