manualshive.com logo in svg

ROBBE-Futaba FX-32, Instruction Manual

Share
Download
ROBBE-Futaba FX-32 Instruction Manual Download Page 18

18

<Before Use>

SD Card (secure digital memory card) (not 

included)

The FX-32 transmitter model data can be stored 

by using any commonly found SD card. When 

FX-32 transmitter update software is released, the 

software is updated using an SD card. The FX-32 

is capable of using SD cards with a memory size 

between 32MB and 2GB.

CAUTION

Be sure to turn off the power to the 

transmitter before inserting or removing 

the SD card.

 As the SD card is a precision device, do not 

use excessive force when inserting.

SD card reader/writer

Saving model data and update files (released 

from Futaba) into the SD card, you can use those 

files on your FX-32 transmitter. Equipment for 

reading and writing SD cards is available at most 

electronics stores. 

Stored data

When you have a problem of saving or reading 

data after a long period of use, please get a new SD 

card.

*We do not have the responsibility of compensating any 

failure or damage to the data stored in the memory card no 

matter what the reason is. Be sure to keep a backup of your 

important data in your SD card.

Inserting/removing the SD card

① A side cover is opened.

② It inserts until it locks SD card into SD card slot.

*It is releasable if a card is pushed once again.

*Don't mistake the 

both sides/ the 

direction of 

SD card.

SD card slot

Stick Adjustment
Adjustment of the stick lever angle

You can make fine adjustments to the angle of 

a stick lever either inwards or outwards from the 

center stick position.

 

●Screw

Use the attached 1.5mm hexagonal wrench 

(inside stylus) to turn the screw clockwise to adjust 

the stick outwards, or counter-clockwise to tilt it 

inward.

Note: Be careful not to turn the screw too far 

counterclockwise as it could fall out.

Summary of Contents for FX-32





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands