
8077
O:Jobs/PGS
*CTL
[0 to 9999999/ 0 / 1 /step]
These SPs count and calculate the number of "Other" application jobs (Web Image
Monitor, Palm 2, etc.) by size based on the number of pages in the job.
8-07x-001 1 Page
8-07x-008
21 to 50 Pages
8-07x-002 2 Pages
8-07x-009
51 to 100 Pages
8-07x-003 3 Pages
8-07x-010
101 to 300 Pages
8-07x-004 4 Pages
8-07x-011
301 to 500 Pages
8-07x-005 5 Pages
8-07x-012
501 to 700 Pages
8-07x-006 6 to 10 Pages
8-07x-013
701 to 1000 Pages
8-07x-007 11 to 20 Pages
8-07x-014
1001 to Pages
• For example: When a print job stored on the document server is printed in document server mode,
the appropriate L: counter (SP8076 0xx) increments.
• Printing a fax report counts as a job and increments the F: counter (SP 8073).
• Interrupted jobs (paper jam, etc.) are counted, even though they do not finish.
• If a job is paused and re-started, it counts as one job.
• If the finisher runs out of staples during a print and staple job, then the job is counted at the time the
error occurs.
• For copy jobs (SP 8072) and scan jobs (SP 8075), the total is calculated by multiplying the
number of sets of copies by the number of pages scanned. (One duplex page counts as 2.)
• The first test print and subsequent test prints to adjust settings are added to the number of pages of
the print job (SP 8072).
• When printing the first page of a job from within the document server screen, the page is counted.
8381
T:Total PrtPGS
*CTL
These SPs count the number of pages printed by the
customer. The counter for the application used for
storing the pages increments.
[0 to 9999999/ 0 / 1 /step]
8384
P:Total PrtPGS
*CTL
8387
O:Total PrtPGS
*CTL
• When several documents are merged for a print job, the number of pages stored are counted for
the application that stored them.
• These counters are used primarily to calculate charges on use of the machine, so the following
pages are not counted as printed pages:
- Blank pages in a duplex printing job.
5. System Maintenance Reference
510
Summary of Contents for Z-P2
