manualshive.com logo in svg

Ricoh AFICIO AP306, Setup Manual

The Ricoh AFICIO AP306 Printer Reference manual is a comprehensive guide for users, providing detailed instructions on how to operate and maintain this high-performance printer. Easily downloadable for free on our website, manualshive.com, it offers valuable insights and assistance, ensuring optimal performance and efficiency for your printing needs.

Share
Download
background image

Draft 2000/06/22

Installing the Memory Unit

17

2

Installing the Memory Unit

R

 

CAUTION:

Important

❒

The memory unit can be damaged
by small amounts of static electric-
ity. Before touching it, you should
touch some metal to remove static
electricity from your body.

A

Turn off the printer's power
switch and remove all cables and
cords from the printer.

B

If you use the duplex printer, re-
move the two screws of the du-
plex unit and then open the unit
slowly.

Note

❒

A coin can be used to remove
the screws.

❒

The duplex unit cannot be re-
moved. Do not apply down-
ward pressure to the duplex
unit while installing options.

❒

After step 

C

, the illustrations

show the simplex printer. The
procedure for the duplex print-
er is identical.

C

Remove the six screws, and re-
move the controller board cover.

Note

❒

A coin can be used to remove
the screws.

D

Confirm that the notch on the
memory unit is on the right.
Tilt the memory unit so that it is 30
degrees perpendicular to slot 2
(

A

), and push it forward (

B

). It

should make click into place. 

1.

slot 1

2.

slot 2

•

Before installing options, the ma-
chine should be turned off and 
unplugged for at least thirty min-
utes. Components inside the 
machine become very hot, and 
can cause a burn injury if 
touched.

ZBGH010E

ZBGP010E

2

1

ZBGP020E

Summary of Contents for AFICIO AP306































































































































































































































































































































































































Reviews:

No comments

Related manuals for AFICIO AP306

Samsung ML-6050 Manual Del Usuario preview
ML-6050
Brand: Samsung Pages: 82
Samsung ML-2525 Datasheet preview
ML-2525
Brand: Samsung Pages: 2
Nantian Electronics PR9 Quick Reference Manual preview
PR9
Brand: Nantian Electronics Pages: 4
Pantum P3000 Series Maintenance Manual preview
P3000 Series
Brand: Pantum Pages: 94
Radio Shack TRS-80 Operation Manual preview
TRS-80
Brand: Radio Shack Pages: 57
Canon RP10 User Manual preview
RP10
Brand: Canon Pages: 37
Xerox Phaser 6180MFP Installation Manual preview
Phaser 6180MFP
Brand: Xerox Pages: 2
Xerox Phaser 6180MFP Features Setup Manual preview
Phaser 6180MFP
Brand: Xerox Pages: 103
Xerox Phaser 6125 Specification preview
Phaser 6125
Brand: Xerox Pages: 2
Xerox DocuPrint 4850 NPS Troubleshooting Manual preview
DocuPrint 4850 NPS
Brand: Xerox Pages: 68
Xerox DocuColor 7002 Quick Start Manual preview
DocuColor 7002
Brand: Xerox Pages: 28
Xerox DocuColor 5000AP User Manual preview
DocuColor 5000AP
Brand: Xerox Pages: 5
Xerox Document WorkCentre 450c Reference Manual preview
Document WorkCentre 450c
Brand: Xerox Pages: 2
Xerox Document WorkCentre 450c User Manual preview
Document WorkCentre 450c
Brand: Xerox Pages: 214
Xerox DocuColor 5750 System Administration Manual preview
DocuColor 5750
Brand: Xerox Pages: 68
Xerox DocuColor 1632 Quick Connect Manual preview
DocuColor 1632
Brand: Xerox Pages: 2
Xerox Phaser 6300 Supplementary Manual preview
Phaser 6300
Brand: Xerox Pages: 4
Xerox PHASER 6140 User Manual preview
PHASER 6140
Brand: Xerox Pages: 170

Brands by name

Popular brands

Load more brands