Ricoh AFICIO AP306 Setup Manual Download Page 109

Page: 109 / 382

Draft 2000/06/22

Paper and Other Media Supported by This Printer

❖

Paper sizes and paper feed directions supported by each paper tray (Inch version)

•

✩

means that the size is supported and needs to select the paper size using

the operation panel. (The bypass tray has no dial on the tray.)

⇒

P.32

“Loading

Paper in the Bypass Tray”

•

❍

means that the size is supported and indicated on the tray dial. Be sure to

set the paper size dial to match the actual paper size loaded in the tray.

•

★

means that the size is supported but not indicated on the paper size dial.

You should set the paper size dial to “

”, and select the paper size using the

operation panel. The default setting is Foolscap (8.5“

13”).

⇒

P.31

“Selecting

paper size using the operation panel”

•

means that the size is not supported.

eed

rec

Size (inch

)

pass tra

tand

ard

tray (Tray

R FE

ED UNIT Typ

e30

ray 2

/3)

12x18

12"

18"

✩

Double Letter

11"

17"

✩

❍

Legal

14"

✩

❍

Letter

11"

✩

❍

Half Letter

✩

★

Executive

✩

❍

★

11.69"

16.54"

✩

❍

B4 JIS

10.12"

14.33"

✩

★

10.12"

14.33"

✩

❍

B5 JIS

10.12"

7.17"

✩

★

8.27"

5.83"

✩

★

B6 JIS

5.04”

7.17”

✩

4.13"

5.83"

✩

Folio

13"

✩

★

Foolscap

13"

✩

★

F/GL

13"

✩

★

Com#10 Env

✩

DL Env

4.33"

8.66"

✩

Custom Size

—

✩

Summary of Contents for AFICIO AP306






























































































































































































































































































































































































Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands

Ricoh AFICIO AP306, Setup Manual

Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands