Ricoh AFICIO AP306 Setup Manual Download Page 121

Page: 121 / 382

Draft 2000/06/22

Loading Paper

Sliding out the Output Tray
Extender

If you load paper larger than A4

11"

, slide out the output tray

extender.

Important

❒

Do not place the rear of the printer
near a wall or touch it with your
hand. This area can become ex-
tremely hot.

Note

❒

The above illustration is the sim-
plex printer. The procedure for the
duplex printer is identical.

❒

After printing, return the output
tray extender to its original posi-
tion.

ZBGH022E

Summary of Contents for AFICIO AP306






























































































































































































































































































































































































Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands

Ricoh AFICIO AP306, Setup Manual

Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands