Ricoh AFICIO AP306 Setup Manual Download Page 297

Page: 297 / 382

Draft 2000/06/22

Using PortNavi

Accessing the Port Settings Dialog Box

This section describes how to access the port settings dialog box to configure No-
tice, Parallel Printing and Recovery Printing.

Reference

For more information about these settings, see PortNavi Help.

Click

[Start]

on the taskbar, point to

[Settings]

, and click

[Printers]

Click the icon of the printer you want to use. On the

[File]

menu, click

[Prop-

erties]

Click the

[Ports]

tab and click

[Configure Port]

The PortNavi settings dialog box appears.

Summary of Contents for AFICIO AP306






























































































































































































































































































































































































Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands

Ricoh AFICIO AP306, Setup Manual

Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands