Ricoh AFICIO AP306 Setup Manual Download Page 24 | Manualshive

Page: 24 / 382

background image

Draft 2000/06/22

Getting Started

4

1

Software and Utilities Included on the CD-
ROM

❖

PRINTER MANAGER FOR ADMINISTRATOR

A utility for the system administrator to manage printers on the network.

Reference

For the name of PRINTER MANAGER FOR ADMINISTRATOR you use,
see the inside of front cover of this manual.
For more information about using PRINTER MANAGER FOR ADMINIS-
TRATOR, see PRINTER MANAGER FOR ADMINISTRATOR Help.

❖

PRINTER MANAGER FOR CLIENT

A utility for users to manage their own print jobs on the network.

Reference

For the name of PRINTER MANAGER FOR CLIENT you use, see the in-
side of front cover of this manual.
For more information about using PRINTER MANAGER FOR CLIENT,
see PRINTER MANAGER FOR CLIENT Help.

❖

Multidirect Print

A utility for printing on a "Peer-to-Peer" network.

Reference

For more information about using Multidirect Print, see the “Operating In-
structions” for the optional Network Interface Board included as a PDF file
on the CD-ROM.

❖

PortNavi

A utility that helps you to use network printers effectively. It is useful in en-
vironments where two or more network printers are used.

Reference

For more information about PortNavi, see the “Operating Instructions” for
the optional Network Interface Board included as a PDF file on the CD-
ROM.

❖

Acrobat Reader

A utility that allows you to read PDF (Portable Document Format).

Note

❒

Documentation about using the printer is included on the CD-ROM in a
PDF format.

«
...
22
23
24
25
26
...
»

Summary of Contents for AFICIO AP306































































































































































































































































































































































































Reviews:

No comments

Related manuals for AFICIO AP306

Brand: Saxxot Pages: 13

Brand: QMS Pages: 27

Brand: QMS Pages: 3

Brand: Oki Pages: 40

Brand: Oki Pages: 104

Brand: Oki Pages: 28

Brand: Oki Pages: 23

Brand: Oki Pages: 108

Brand: Oki Pages: 2

Brand: Oki Pages: 94

Brand: Oki Pages: 135

Brand: Oki Pages: 97

Brand: Oki Pages: 280

Brand: Oki Pages: 123

Pacemark PM4410

Brand: Oki Pages: 144

Pacemark PM4410

Brand: Oki Pages: 28

Brand: Oki Pages: 176

Brand: Olivetti Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands