manualshive.com logo in svg

Ricoh AFICIO AP306, Setup Manual

The Ricoh AFICIO AP306 Printer Reference manual is a comprehensive guide for users, providing detailed instructions on how to operate and maintain this high-performance printer. Easily downloadable for free on our website, manualshive.com, it offers valuable insights and assistance, ensuring optimal performance and efficiency for your printing needs.

Share
Download
background image

Draft 2000/06/22

Getting Started

8

1

Exterior-Rear View

Simplex printer

1.

Paper Exit Cover

Open this cover when removing misfed
paper from the fusing unit.

2.

Ozone Filter

This filter reduces the amount of ozone
that is discharged into the air.

3.

Ventilator

Allows air to be discharged, preventing
components inside the printer from over-
heating.

Important

❒

Do not leave the ventilator ob-
structed or blocked. Doing so cre-
ates the danger of malfunction due
to overheating.

4.

Controller Board Cover

Remove to install some options.

5.

Interface Board Cover

Remove to install optional interface
boards.

Important

❒

Rating voltage of the network in-
terface port for the network: Max.
DC 5 V.

❒

Rating voltage of the parallel inter-
face port for the computer: Max.
DC 5 V.

6.

Ventilator

Allows air to enter, preventing compo-
nents inside the printer from overheat-
ing.

Important

❒

Do not leave the ventilator ob-
structed or blocked. Doing so cre-
ates the danger of malfunction due
to overheating.

7.

Parallel Interface Port

Plug the parallel cable that connects the
printer to the computer into this port.

Important

❒

Rating voltage of the parallel inter-
face port for the computer: Max.
DC 5 V.

8.

Power Connector

Connect the power cord to this connec-
tor.

ZBGX070E

1

2

3

5

4

6 7

8

Summary of Contents for AFICIO AP306































































































































































































































































































































































































Reviews:

No comments

Related manuals for AFICIO AP306

GCC Technologies Elite 12N Network Manual preview
Elite 12N
Brand: GCC Technologies Pages: 63
gCreate gMax 2 PRO Unboxing And Setup Instructions preview
gMax 2 PRO
Brand: gCreate Pages: 9
GCC Technologies Elite XL-1208 Supplementary Manual preview
Elite XL-1208
Brand: GCC Technologies Pages: 9
GCC Technologies Elite XL-1208 Install Manual preview
Elite XL-1208
Brand: GCC Technologies Pages: 12
gCreate gMax 2 PRO User Manual preview
gMax 2 PRO
Brand: gCreate Pages: 21
GCC Technologies Elite XL User Manual preview
Elite XL
Brand: GCC Technologies Pages: 199
Xerox DocuColor 6060 Recommended Materials List preview
DocuColor 6060
Brand: Xerox Pages: 4
Lexmark 7016-630 Service Manual preview
7016-630
Brand: Lexmark Pages: 455
Oce im4511 Operation Manual preview
im4511
Brand: Oce Pages: 8
Belkin F1UP0001uk Basic Manual preview
F1UP0001uk
Brand: Belkin Pages: 8
MUTOH VJ-1938TX Operation Manual preview
VJ-1938TX
Brand: MUTOH Pages: 148
Axiohm TPOSS001 Setup Manual preview
TPOSS001
Brand: Axiohm Pages: 6
SPRT SP-POS5810 User Manual preview
SP-POS5810
Brand: SPRT Pages: 12
Copystar CS-C3225E Specifications preview
CS-C3225E
Brand: Copystar Pages: 1
QMS qms-ps 800+ User Manual preview
qms-ps 800+
Brand: QMS Pages: 188
Sinfonia Technology DP-1045 Operation Manual preview
DP-1045
Brand: Sinfonia Technology Pages: 41
Canon MP282 Manual preview
MP282
Brand: Canon Pages: 707
Canon NP3050 Service Manual preview
NP3050
Brand: Canon Pages: 339

Brands by name

Popular brands

Load more brands