Ricoh AFICIO AP306 Setup Manual Download Page 299

Page: 299 / 382

Draft 2000/06/22

Using Multidirect Print

Uninstalling Multidirect Print

Open

[Control Panel]

, and double-click the

[Add/Remove Programs]

icon.

Click

[Change or Remove Programs]

, click

[Multidirect Print]

, and click

[Change/

Remove]

After a confirmation message appears, click

[Yes]

UninstallShield removes all of the components of Multidirect Print.

When the uninstallation is complete, restart the computer.

Setting Up the Printer Driver

Multidirect Print cannot be used until the printer driver is installed and the cor-
rect port is selected.

Preparation

The target printer must be turned on before starting the installation process.

Install the printer drivers.

If the printer drivers have already been installed, you can proceed to the next
step.

Reference

For more information about installing the printer drivers, see the "Setup
Guide" that comes with the printer.

Note

❒

Any port can be selected during the installation, however, LPT1 is recom-
mended.

From the

[Printers]

window, click the icon of the printer you want to use. On

the

[File]

menu, click

[Properties]

Click the

[Ports]

tab, and click

[Add Port]

In the

[Available Printer Ports]

box, click

[Multidirect Print]

, and then click

[New

Port]

The

[Add Port]

dialog box appears, and the printers which can be printed to by

TCP/IP are displayed.

Limitation

❒

If PRINTER MANAGER FOR CLIENT is not installed on the computer,
printers which can be printed to by TCP/IP are not displayed. For more in-
formation about how to install the program, see the "Setup Guide" that
comes with the printer.

Summary of Contents for AFICIO AP306






























































































































































































































































































































































































Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands

Ricoh AFICIO AP306, Setup Manual

Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands