Ricoh AFICIO AP306 Setup Manual Download Page 303 | Manualshive

Page: 303 / 382

background image

Draft 2000/06/22

Setting up a Client Computer

29

2

Setting up a Client Computer

This section describes the procedures for setting up a client in a network that
uses Windows 2000, Windows NT Server or Windows NT Workstation as a
print server.
To print from Windows 2000, you must install the printer driver and change the
printer port to the print server.

Note

❒

This section assumes that the client has already been configured to communi-
cate with a Windows 2000 or Windows NT print server. Do not begin the fol-
lowing procedure until the client has been set up and configured correctly.

Use the

[Printers]

window to set up the printer.

A

Click

[Start]

, point to

[Settings]

, and then click

[Printers]

.

B

Double-click the

[Add Printer]

icon.

This launches the Add Printer Wizard.

C

Click

[Next >]

.

D

Click

[Network printer]

, and click

[Next >]

.

E

In the

[Shared printers:]

box, double-click the name of the computer used as

a print server.

The printers attached to the network are displayed.

F

Click the printer you want to use, and click

[Next >]

.

Windows 2000

Windows 2000 or
Windows NT Print Server

«
...
301
302
303
304
305
...
»

Summary of Contents for AFICIO AP306































































































































































































































































































































































































Reviews:

No comments

Related manuals for AFICIO AP306

Brand: Xerox Pages: 48

Brand: Oce Pages: 4

Brand: B3 innovations Pages: 12

Brand: Raise3D Pages: 32

Brand: Raymarine Pages: 135

Brand: Xerox Pages: 13

Brand: Xerox Pages: 16

Brand: Lanier Pages: 298

6130N - Phaser Color Laser Printer

Brand: Xerox Pages: 2

6130N - Phaser Color Laser Printer

Brand: Xerox Pages: 2

Brand: Canon Pages: 4

Brand: Konica Minolta Pages: 846

Brand: Felix Storch Pages: 46

INFOPRINT HI-LITE COLOR 4005-HC2

Brand: IBM Pages: 10

AltaLink C81 Series

Brand: Xerox Pages: 412

Brand: Konica Minolta Pages: 8

Brand: Savin Pages: 132

Brand: IBM Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands