Ricoh AFICIO AP306 Setup Manual Download Page 277

Page: 277 / 382

Draft 2000/06/22

Configuring Protocols

Configure the TCP/IP protocol with the appropriate IP address, subnet
mask and other settings.

Confirm with the network administrator that the settings are correct.

Configuring NetBEUI for Printing

Follow these instructions to configure the Network Interface Board and Win-
dows 95/98 to use the NetBEUI protocol.

Configuring the printer

Configure the printer to use the NetBEUI protocol.
• Confirm that the NetBEUI protocol is set to be active. (The factory default is

active.)

Reference

For more information about how to make the above settings, see the "Setup
Guide" that comes with the printer.

Configuring a Windows 95/98 computer

Install the NetBEUI protocol on the Windows 95/98 computer and set it as the
default protocol.

Open

[Control Panel]

and double-click the

[Network]

icon. Confirm that “Net-

BEUI” is listed in the

[The following network components are installed:]

box on

the

[Configuration]

tab.

Note

❒

If the NetBEUI protocol is not installed, click

[Add]

on the

[Configuration]

tab

and install it. For more information about installing the NetBEUI protocol,
see Windows 95/98 Help.

❒

If “NetBEUI ->Dial-Up Adaptor” is listed in the

[The following network com-

ponents are installed:]

box, select it and click

[Remove]

to remove the binding.

Set the NetBEUI protocol as the default protocol. Click the

[Configuration]

tab, select “NetBEUI” in the

[The following network components are installed:]

box, and click

[Properties]

Click the

[Advanced]

tab, select

[Set this protocol to be the default protocol]

, and

click

[OK]

Click

[OK]

to close the

[Network]

dialog box.

When the message to restart appears, click

[Yes]

Summary of Contents for AFICIO AP306






























































































































































































































































































































































































Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands

Ricoh AFICIO AP306, Setup Manual

Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands