Ricoh AFICIO AP306 Setup Manual Download Page 309 | Manualshive

Page: 309 / 382

background image

Draft 2000/06/22

Using PortNavi

35

3

Using PortNavi

PortNavi is a utility that helps you to use network printers effectively. It is useful
in environments where two or more network printers are used. It is recommend-
ed that you install PortNavi to use Parallel Printing and Recovery Printing. For
more information about PortNavi, see PortNavi Help.

❖

PortNavi features

• Send a print job directly to the network printers without using a print serv-

er.

• Notification when a printing error occurs.
• Print documents using other printers in the printer group when the speci-

fied printer is busy (Recovery Printing).

Important

❒

The following must be the same for the specified printer and the print-
ers selected for Recovery Printing.
• Printer models
• Installed options (e.g. Paper Tray)
• Size and orientation of paper in each paper tray
• Total memory
• Installed fonts (including the downloaded fonts)

• Equally divide the number of copies to be printed among the selected

printers in the printer group (Parallel Printing).

Important

❒

The following must be the same for the specified printer and the print-
ers selected for Parallel Printing.
• Printer models
• Installed options (e.g. Paper Tray)
• Size and orientation of paper in each paper tray
• Total memory
• Installed fonts (including the downloaded fonts)

Limitation

❒

To use PortNavi you must install PRINTER MANAGER FOR CLIENT and
use the TCP/IP protocol. For the name of the PRINTER MANAGER FOR
CLIENT you use, see the inside the front cover of this manual.

❒

For more information about installing PRINTER MANAGER FOR CLIENT,
see the “Setup Guide” that comes with the printer.

❒

On a computer that is used as a print server, do not use the features such as
Parallel Printing, Recovery Printing and Notify. For more information about
turning off these features, see PortNavi Help.

«
...
307
308
309
310
311
...
»

Summary of Contents for AFICIO AP306































































































































































































































































































































































































Reviews:

No comments

Related manuals for AFICIO AP306

Color imageCLASS MF8580Cdw

Brand: Canon Pages: 750

ImageCLASS 2300

Brand: Canon Pages: 8

Color imageCLASS MF8580Cdw

Brand: Canon Pages: 750

Color imageCLASS 8180c

Brand: Canon Pages: 95

Brand: Canon Pages: 4

Brand: Canon Pages: 49

ImageCLASS 2300

Brand: Canon Pages: 156

Brand: Canon Pages: 193

Brand: QMS Pages: 24

imageCLASS D1120

Brand: Canon Pages: 36

ImageCLASS 2300

Brand: Canon Pages: 44

Brand: Canon Pages: 66

Brand: Canon Pages: 12

imagePROGRAF iPF8300S

Brand: Canon Pages: 52

Brand: Canon Pages: 2

Brand: Magicard Pages: 26

Brand: QMS Pages: 194

Brand: Z Corporation Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands