Ricoh AFICIO AP306 Setup Manual Download Page 276 | Manualshive

Page: 276 / 382

background image

Draft 2000/06/22

Windows 95/98 Configuration

2

1

Configuring Protocols

Configuring TCP/IP and IPP for Printing

Follow these instructions to configure the Network Interface Board and Win-
dows 95/98 to use the TCP/IP protocol and IPP.

Configuring the printer

Configure the printer to use the TCP/IP protocol.
• Confirm that the TCP/IP protocol is set to be active. (The factory default is ac-

tive.)

• Assign an IP address and make other settings required for using the TCP/IP

protocol.

Reference

For more information about how to make the above settings, see the "Setup
Guide" that comes with the printer.
If DHCP is used to assign IP addresses, see P.101

“When Using DHCP”

.

Note

❒

After setting the IP address, use the ping command to confirm that it has been
set correctly.

A

Click

[Start]

, point to

[Programs]

, and then click

[MS-DOS Prompt]

.

B

Type the following. (Example IP address is 192.168.15.16)

C:> ping 192.168.15.16

If the address has been configured correctly, the following message ap-
pears.

Reply from 192.168.15.16 : bytes=32 time<10ms TTL=32

If the address has been configured incorrectly, the following message ap-
pears.

Request timed out.

Configuring a Windows 95/98 computer

Follow these steps to configure a Windows 95/98 computer to use the TCP/IP
protocol.

A

Open

[Control Panel]

and double-click the

[Network]

icon. Confirm that “TCP/

IP” is listed in the

[The following network components are installed:]

box on the

[Configuration]

tab.

Note

❒

If the TCP/IP protocol is not installed, click

[Add]

on the

[Configuration]

tab

and install it. For more information about installing the TCP/IP protocol,
see Windows 95/98 Help.

«
...
274
275
276
277
278
...
»

Summary of Contents for AFICIO AP306































































































































































































































































































































































































Reviews:

No comments

Related manuals for AFICIO AP306

Brand: IBM Pages: 16

Brand: YOUPAI Pages: 15

Brand: TallyGenicom Pages: 15

Brand: Acadian Robotics Pages: 2

Brand: Xerox Pages: 262

Brand: TallyGenicom Pages: 2

Brand: Oki Pages: 255

WorkCentre 7328

Brand: Xerox Pages: 8

Brand: Xerox Pages: 20

Brand: Ricoh Pages: 74

Brand: Oki Pages: 18

Brand: Oki Pages: 20

AltaLink C81 Series

Brand: Xerox Pages: 412

3600B - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

Brand: Ouring Pages: 54

Brand: Lexmark Pages: 60

Brand: Canon Pages: 8

Brand: Canon Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands