Ricoh AFICIO AP306 Setup Manual Download Page 321 | Manualshive

Page: 321 / 382

background image

Draft 2000/06/22

47

4. NetWare Configuration

This chapter describes how to configure the printer to use as a print server or a
remote printer in a NetWare environment.

Note

❒

NetWare must be set to active using the operation panel of the printer. For
more information about how to set it, see the "Setup Guide" that comes with
the printer.

Installing the NIB Setup Tool

A utility called the NIB Setup Tool is provided to configure the printer to work
in a network environment. This section describes how to install PRINTER MAN-
AGER FOR ADMINISTRATOR, and how to run the NIB Setup Tool.

Limitation

❒

The NIB Setup Tool is supported to work with the following operating sys-
tems.
• Microsoft Windows 95/98
• Microsoft Windows 2000
• Microsoft Windows NT 4.0

Installing PRINTER MANAGER FOR ADMINISTRATOR

Follow these steps to install PRINTER MANAGER FOR ADMINISTRATOR.

Preparation

You should install PRINTER MANAGER FOR ADMINISTRATOR on the
computer. If you install PRINTER MANAGER FOR ADMINISTRATOR from
a file server or run it via the network, PRINTER MANAGER FOR ADMINIS-
TRATOR might not work correctly.
Be sure to close all applications before starting the installation procedure.

A

Close all the applications that are currently running.

B

Insert the CD-ROM labeled “Printer Drivers and Utilities” into the CD-
ROM drive.

If the installer starts automatically, follow the instructions on the screen.
If not, go to step

C

.

C

Open

[Control Panel]

, and double-click the

[Add/Remove Programs]

icon.

D

On the

[Install/Uninstall]

tab, click

[Install]

.

«
...
319
320
321
322
323
...
»

Summary of Contents for AFICIO AP306































































































































































































































































































































































































Reviews:

No comments

Related manuals for AFICIO AP306

Brand: D-Link Pages: 38

Epress EtherNetwork DP-301P+

Brand: D-Link Pages: 2

Brand: DataCard Pages: 2

DocuPrint C525 A

Brand: Xerox Pages: 49

DocuPrint C2100

Brand: Xerox Pages: 206

Brand: Xerox Pages: 116

Brand: Xerox Pages: 358

Brand: Xerox Pages: 344

Brand: Xerox Pages: 59

Brand: Xerox Pages: 2

Brand: Xerox Pages: 10

Brand: Xerox Pages: 51

Brand: Xerox Pages: 110

7300DX - Phaser Color Laser Printer

Brand: Xerox Pages: 8

Brand: Xerox Pages: 220

Brand: Xerox Pages: 28

8400B - Phaser Color Solid Ink Printer

Brand: Xerox Pages: 203

3150 - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands