Ricoh AFICIO AP306 Setup Manual Download Page 342

Page: 342 / 382

Draft 2000/06/22

NetWare Configuration

Windows NT 4.0

Follow the procedure to set up a Windows NT 4.0 client.

Preparation

Log on to the NetWare file server before starting the following procedure.

Double-click the

[Network Neighborhood]

icon on the desktop and navigate to

the queue you want to use, and then double-click it.

The

[Printers]

dialog box appears.

Click

[No]

Close all the applications that are currently running.

Insert the CD-ROM into the CD-ROM drive.

If the setup menu starts automatically, you can go to the next step. If not, see
the "Setup Guide" that comes with the printer.

The

[Printer Installation]

dialog box appears.

From the

[Port]

list, select the queue you selected in step

, and click

[Next >]

Follow the instructions on the screen to finish the installation of the printer
driver.

Summary of Contents for AFICIO AP306






























































































































































































































































































































































































Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands

Ricoh AFICIO AP306, Setup Manual

Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands