manualshive.com logo in svg

Ricoh AFICIO AP306, Setup Manual

The Ricoh AFICIO AP306 Printer Reference manual is a comprehensive guide for users, providing detailed instructions on how to operate and maintain this high-performance printer. Easily downloadable for free on our website, manualshive.com, it offers valuable insights and assistance, ensuring optimal performance and efficiency for your printing needs.

Share
Download
background image

Draft 2000/06/22

31

3. Windows NT 4.0

Configuration

Configuring Windows NT 4.0

Printing Without Using a Print Server

The following procedure describes how to configure Windows NT 4.0 to use the
printer on a network without a Windows 2000, Windows NT Server, Windows
NT Workstation or NetWare based print server.

Printing with a LPR Port

See P.44 

“Configuring LPR Port Printing”

 for how to configure a LPR port in Win-

dows NT 4.0.

Printing with a Windows 2000 or Windows NT Print Server

See P.44 

“Configuring LPR Port Printing”

 for how to configure Windows NT 4.0

with a Windows 2000 or Windows NT print server.

Consult your network administrator about which of the three protocols are appropriate.

2.  Configure the chosen protocol

3.  Select the appropriate software

1.  Decide on the protocol to use

         TCP/IP

4.  Install the software and set the printer driver port

"Using PortNavi"

"Using Multidirect Print"

PortNavi

"Configuring TCP/IP and IPP for Printing"

"Configuring NetBEUI
   for Printing"

Multidirect Print

If using TCP/IP ...

I f   u s i n g   I P P  o r   N e t B E U I   . . .

indicates topics explained in this document

IPP

NetBEUI

Summary of Contents for AFICIO AP306































































































































































































































































































































































































Reviews:

No comments

Related manuals for AFICIO AP306

Unitech MP200 Product Reference Manual preview
MP200
Brand: Unitech Pages: 18
Unitech MP200 Developer'S Manual preview
MP200
Brand: Unitech Pages: 26
Panduit MP200 Firmware Update Instruction Manual preview
MP200
Brand: Panduit Pages: 6
Canon PIXMA MX882 Series Network Setup Manual preview
PIXMA MX882 Series
Brand: Canon Pages: 34
Canon MX470 Getting Started preview
MX470
Brand: Canon Pages: 4
Canon MX470 User Manual preview
MX470
Brand: Canon Pages: 913
Canon Laser Class 700 Series Setup Manual preview
Laser Class 700 Series
Brand: Canon Pages: 30
Canon Laser Class 700 Series Datasheet preview
Laser Class 700 Series
Brand: Canon Pages: 6
Canon Laser Class 700 Series Specification preview
Laser Class 700 Series
Brand: Canon Pages: 6
Canon Laser Class 700 Series Network Manual preview
Laser Class 700 Series
Brand: Canon Pages: 108
Canon PIXMA MX860 series Network Manual preview
PIXMA MX860 series
Brand: Canon Pages: 9
Canon imagePROGRAF iPF9400 Brochure & Specs preview
imagePROGRAF iPF9400
Brand: Canon Pages: 8
Canon PIXMA MX860 series Getting Started Manual preview
PIXMA MX860 series
Brand: Canon Pages: 93
Canon MP980 series Manual preview
MP980 series
Brand: Canon Pages: 20
Canon PIXMA MX922 Setup Manual preview
PIXMA MX922
Brand: Canon Pages: 30
Canon PIXMA MX922 Easy Setup preview
PIXMA MX922
Brand: Canon Pages: 2
Ier I420 User Safety And Start Manual preview
I420
Brand: Ier Pages: 8
Olympus P-10 Instruction preview
P-10
Brand: Olympus Pages: 2

Brands by name

Popular brands

Load more brands