Ricoh AFICIO AP306 Setup Manual Download Page 69 | Manualshive

Page: 69 / 382

background image

Draft 2000/06/22

Installing the RICOH-SCRIPT2 Printer Driver

49

4

Note

❒

The versions of the LaserWriter driver are separated into two categories.
"LaserWriter 8.3x or earlier" refers to the LaserWriter 8.3x driver and all driv-
ers before that. "LaserWriter 8.4x or later" refers to LaserWriter 8.4x, 8.5x and
8.6x. LaserWriter 8.5x was used to make this manual. The settings may differ
depending on the version of the LaserWriter driver being used.

Installing the PPD files

Limitation

❒

Be sure to install the PPD file correctly. If not installed correctly, you cannot
use it, even though it is physically installed on the printer.

A

Start the Macintosh.

B

Double-click the hard disk icon, and then double-click the

[Extensions]

fold-

er inside the

[System Folder]

.

C

Insert the CD-ROM into the CD-ROM drive.

D

Double-click the CD-ROM icon.
The contents of the CD-ROM appear.

E

Double-click the

[PRINTER DESCRIPTIONS]

folder in the CD-ROM, and then

double-click the folder having the appropriate language name.

F

Select the appropriate PPD file for the printer.

G

Copy the PPD file in the

[Printer Descriptions]

folder located inside the

[Exten-

sions]

folder.

The PPD file is installed.

Installing the ColorSync profiles

ColorSync profiles make it possible for the printer to print colors of similar in-
tensity to those that appear on the computer display. You must install the Col-
orSync profiles to use this feature.

Note

❒

The ColorSync profiles conform with the color characteristics defined by the
International Color Consortium (ICC).

❒

Some computer displays may require particular settings to be controlled by
ColorSync. For more information, see the documentation that comes with
your display.

The following profiles are provided for the printer.

«
...
67
68
69
70
71
...
»

Summary of Contents for AFICIO AP306































































































































































































































































































































































































Reviews:

No comments

Related manuals for AFICIO AP306

Pixma G1000 series

Brand: Canon Pages: 2

Pixma G1000 series

Brand: Canon Pages: 80

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 44

Brand: Canon Pages: 11

Brand: Canon Pages: 2

Brand: Canon Pages: 12

PIXMA Pro9000 Mark II Series

Brand: Canon Pages: 4

Brand: Xerox Pages: 192

Brand: LabelTac Pages: 2

Brand: Olivetti Pages: 2

Brand: Olivetti Pages: 109

Brand: Olivetti Pages: 111

Brand: Olivetti Pages: 8

Brand: Ricoh Pages: 268

Brand: QMS Pages: 180

Brand: Muratec Pages: 6

Brand: Konica Minolta Pages: 44

Brand: idp Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands