Ricoh AFICIO AP306 Setup Manual Download Page 373 | Manualshive

Page: 373 / 382

background image

Draft 2000/06/22

Precautions

99

6

Precautions

Please pay attention to the following when using the Network Interface Board.
When configuration is necessary, follow the appropriate procedures below.

Connecting a Dial Up Router to a Network

When the NetWare file server and the printer are on the opposite side of a router,
packets are continuously sent back and forth, possibly causing communications
charges to increase. Because the packet transmission is a specification of Net-
Ware, you need to change the configuration of the router. If the network you are
using does not allow you to configure the router, configure the printer.

Configuring the router

Filter the packets so that they do not pass over the dial up router.

Note

❒

The MAC address of the printer doing the filtering is printed on the printer
configuration page. For more information about printing a configuration
page, see the "Setup Guide" that comes with the printer.

❒

For more information about configuring the printer if the router cannot be
configured, see the instructions below.

Configuring the printer with NetWare

A

Following the setup method in this manual, configure the file server.

B

Set the frame type for a NetWare environment.

Reference

For more information about selecting a frame type, see the "Setup Guide"
that comes with the printer.

Configuring the printer without NetWare

A

While not printing, the Network Interface Board sends packets on the net-
work. Set the NetWare to inactive.

Reference

For more information about selecting a protocol, see the "Setup Guide" that
comes with the printer.

«
...
371
372
373
374
375
...
»

Summary of Contents for AFICIO AP306































































































































































































































































































































































































Reviews:

No comments

Related manuals for AFICIO AP306

Brand: QMS Pages: 122

Brand: QMS Pages: 306

Brand: DataCard Pages: 8

Brand: DataCard Pages: 8

Brand: DataCard Pages: 3

RS/6000 44P Series 270

Brand: IBM Pages: 216

imagePROGRAF GP-540

Brand: Canon Pages: 82

Brand: Oce Pages: 209

Magicolor 4650DN

Brand: Konica Minolta Pages: 260

Brand: Xerox Pages: 214

Brand: Cardco Pages: 28

Brand: Ricoh Pages: 2

Brand: RHINO Pages: 21

Brand: Kyocera Pages: 392

WORKCENTRE 7428

Brand: Xerox Pages: 208

Brand: Ricoh Pages: 8

Brand: Epson Pages: 97

Brand: Epson Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands