Ricoh AFICIO AP306 Setup Manual Download Page 180

Page: 180 / 382

Draft 2000/06/22

Using the Operation Panel

❖

E.Print Errors

You can select if an error report should be printed from the current tray when
a PostScript error occurs while printing.
•

Off

No error report is printed when an error occurs.

• On

An error report is printed when an error occurs. It uses some of the VM
area to turn this feature on.

❖

F.KTalk Mode

This setting is not available.

❖

G.Parallel IF1

You can select the parallel interface timing. When “SystemDefault” is select-
ed, the setting in the “System Menu” is used.
•

SystemDefault

• ACK Inside
• ACK Outside

❖

H.Parallel IF2

You can select the parallel interface timing. When “SystemDefault” is select-
ed, the setting in the “System Menu” is used.
•

SystemDefault

• ACK Inside
• ACK Outside

Important

❒

Do not use the “ACK Outside” setting.

System Menu

The following are the settings you can make with the “System Menu”.

Note

❒

Italicized settings indicate default settings.

❖

1. Paper Tray

You can select the default paper tray that is selected whenever you turn on
the printer.
•

Tray1

• Tray2 (option)
• Tray3 (option)
• Bypass

Summary of Contents for AFICIO AP306






























































































































































































































































































































































































Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands

Ricoh AFICIO AP306, Setup Manual

Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands