Ricoh AFICIO AP306 Setup Manual Download Page 195

Page: 195 / 382

Draft 2000/06/22

Administering Printing by User Code

109

Press

{T}

{U}

to display "Maintenance", and then press

{

Enter

}

<Menu>

Maintenance

The following message appears on the panel display.

1.Reinstall

Press

{T}

{U}

to display "8.Log Protect", and then press

{

Enter

}

8.Log Protect

The following message appears on the panel display.

Press

{T}

{U}

to select “On” or “Off”, and then press

{

Enter

}

Off

This registers the setting and returns to the “Maintenance” menu.

Press

{

On Line

}

The "Ready" message appears on the panel display.

Deleting the User Code Record

This procedure describes how to clear the User Code record.

Note

❒

If “Log Protect" is set to "On", you can not delete the User Code record. Select
"Off" in “Log Protect", and then follow the procedure below.

⇒

P.108

“Protect-

ing the User Code Record”

Check if the On Line indicator stays on. If not, press

{

On Line

}

Summary of Contents for AFICIO AP306






























































































































































































































































































































































































Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands

Ricoh AFICIO AP306, Setup Manual

Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands