Ricoh AFICIO AP306 Setup Manual Download Page 302

Page: 302 / 382

Draft 2000/06/22

Windows 2000 Configuration

Configuring LPR Port Printing

This section explains the procedure for printing to a LPR port from Windows
2000.

Note

❒

The TCP/IP protocols must be installed and configured correctly. For more
information about configuring the protocol, see P.17

“Configuring TCP/IP and

IPP for Printing”

Click

[Start]

, point to

[Settings]

, and then click

[Printers]

The

[Printers]

window appears.

Click the icon of the printer you want to use. On the

[File]

menu, click

[Prop-

erties]

In the

[Available port types:]

box, click “LPR Port”, and then click

[New Port]

Note

❒

If “LPR Port” does not appear, “Print Services for Unix” has not been in-
stalled.

Type the IP address of the Network Interface Board into the

[Name or address

of server providing lpd:]

box.

Type “lp” into the

[Name of printer or print queue on that server box:]

, and click

[OK]

Click

[Close]

Confirm that the port name is displayed in the

[Print to the following port(s)]

box and the check mark is inside the check box, and then click

[OK]

Summary of Contents for AFICIO AP306






























































































































































































































































































































































































Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands

Ricoh AFICIO AP306, Setup Manual

Search results

Summary of Contents for AFICIO AP306

Reviews:

Related manuals for AFICIO AP306

Brands by name

Popular brands