manualshive.com logo in svg

Printronix P8000 Series, Administrator'S Manual

The Printronix P8000 Series is a high-performance line matrix printer known for its reliability and efficiency. For those looking to customize and optimize their printing experience, the Administrator's Manual is available for free download from manualshive.com. Get the manual today and unleash the full potential of your printer.

Share
Download
background image

Position the Paper Input and Adjust the Paper Guides

351

Figure 2. Adjusting Paper Guide Leaves

4. Slide the left outboard mount block so that the left outer paper guide leaf 

is .5 inches from the left tractor. (See Figure 2).

5. Slide the right outboard mount block so that the right outer paper guide 

leaf is .5 inches from the right tractor.

6. Slide the center mount block so that the center paper guide leaf is 

centered between the left and right outer paper guide leaves.

7. Install the paper guide knobs and front paper guide leaves. 

 

(See Figure 1.)

18

34

85

b

Paper

Tractor (2)

Outer Paper 

Guide Leaf (2)

Center Paper 

Guide Leaf

.5

''

 

.5

''

 

Outboard Mount 

Block (2)

Center Mount 

Block

Summary of Contents for P8000 Series







































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P8000 Series

MAKERGEAR Ultra One User Manual preview
Ultra One
Brand: MAKERGEAR Pages: 8
Xerox Phaser 6140N Compatibility Manual preview
Phaser 6140N
Brand: Xerox Pages: 3
Xerox DocuColor 240 Booklet Creation For Copy preview
DocuColor 240
Brand: Xerox Pages: 2
Xerox WorkCentre 3615 Quick Use Manual preview
WorkCentre 3615
Brand: Xerox Pages: 20
Oki ES9466 Manual preview
ES9466
Brand: Oki Pages: 52
Tally T2240/24 Operator'S Manual preview
T2240/24
Brand: Tally Pages: 28
Lanier LD1110 Operating Instructions Manual preview
LD1110
Brand: Lanier Pages: 234
Wang 2231W-1 Maintenance Manual preview
2231W-1
Brand: Wang Pages: 181
PhotoCentric Liquid Crystal Opus User Manual preview
Liquid Crystal Opus
Brand: PhotoCentric Pages: 12
TRAK 3ntr Series Installation & Printing Manual preview
3ntr Series
Brand: TRAK Pages: 98
Olivetti d-Copia 45 Operation Manual preview
d-Copia 45
Brand: Olivetti Pages: 246
TEC B-470-QQ Series Owner'S Manual preview
B-470-QQ Series
Brand: TEC Pages: 32
Tascam P11/TAS Technical Documentation preview
P11/TAS
Brand: Tascam Pages: 2
Microcom 428M Operator'S Manual preview
428M
Brand: Microcom Pages: 207
Citizen Swift 120D User Manual preview
Swift 120D
Brand: Citizen Pages: 44
Oki ES4140dn User Manual preview
ES4140dn
Brand: Oki Pages: 69
Olivetti d-Copia 1801MF Plus Service Manual preview
d-Copia 1801MF Plus
Brand: Olivetti Pages: 492
Oki ES9160 Maintenance Manual preview
ES9160
Brand: Oki Pages: 1087

Brands by name

Popular brands

Load more brands