NEC VR4181 mPD30181 User Manual Download Page 156

Page: 156 / 444

User’s Manual U14272EJ3V0UM

156

CHAPTER 8 CLOCKED SERIAL INTERFACE UNIT (CSI)

8.1 Overview

The CSI manages communication via a synchronous serial bus. The CSI of the V

4181 has the following key

characteristics:

•

Slave-only synchronous serial interface

•

Able to transmit and receive data simultaneously

•

Supports fixed 8-bit character length

•

Supports burst lengths of 1 to 65535 bits

•

Continuous transfer mode for of peripherals supporting auto-scan

•

Programmable clock phase and clock polarity

The CSI interface shares pins with GPIO signals as follows. When using the CSI, set these pins to use as CSI

signals in the registers of the GIU in advance.

GPIO Pin

CSI Signal

Definition

GPIO10

FRM

Optional multifunction control input. In one mode, FRM determines data direction (transmit

or receive). In the other mode, FRM enables (low level) or inhibits (high level)

transmissions.

GPIO2

SCK

Serial clock input (Maximum frequency: 1.6 MHz)

GPIO1

Serial data output

GPIO0

Serial data input

Caution No clock is supplied to the CSI in the initial state. When using the CSI, set the MSKCSUPCLK bit

of the CMUCLKMSK register in the MBA Host Bridge to 1 in advance so that a clock is supplied.

8.2 Operation of CSI

8.2.1 Transmit/receive operations

Transmit and receive operations are initiated by an external master to drive the serial clock, SCK. The

characteristics of the protocol are controlled by the CSIMODE register, in particular by CKPOL, CKMD, FRMEN, and

FRMMD bits. CKPOL and CKMD bits control the relationship between data driven on SO and SI, and the phase of

the serial clock input to SCK. FRMEN and FRMMD bits enable and control the FRM input.

Summary of Contents for VR4181 mPD30181





























































































































































































































































































































































































































































Search results

Summary of Contents for VR4181 mPD30181

Reviews:

Related manuals for VR4181 mPD30181

Brands by name

Popular brands

NEC VR4181 mPD30181, User Manual

Search results

Summary of Contents for VR4181 mPD30181

Reviews:

Related manuals for VR4181 mPD30181

Brands by name

Popular brands