NEC VR4181 mPD30181 User Manual Download Page 198

Page: 198 / 444

CHAPTER 10 POWER MANAGEMENT UNIT (PMU)

User’s Manual U14272EJ3V0UM

198

10.5.4 Activation via DCD interrupt request

When the DCD1# signal is asserted, the PMU asserts the POWERON signal to provide an external notification

that the CPU core is being activated. After asserting the POWERON signal, the PMU checks the BATTINH signal and

then de-asserts the POWERON signal.

If the BATTINH signal is at high level, the PMU cancels the peripheral unit reset and starts the Cold Reset

sequence to activate the CPU core.

If the BATTINH signal is at low level, the PMU sets 1 to the BATTINH bit in the PMUINTREG register and then

performs another shutdown. After the CPU core is restarted, the BATTINH bit must be checked and cleared to 0 by

software.

The DCDST bit in the PMUINTREG register does not indicate whether a DCD interrupt has occurred but instead

reflects the current status of the DCD1# pin.

Cautions1. The PMU cannot recognize changes in the DCD1# signal while the POWER signal is asserted.

If the DCD1# state when the POWER signal is asserted is different from that when the POWER

signal is deasserted, the change in the DCD1# signal is detected only after the POWER signal

is deasserted. However, if the DCD1# state when the POWER signal is asserted is the same as

that when the POWER signal is deasserted, any changes in the DCD1# signal that occur while

the POWER signal is asserted are not detected.

2. The changes in the DCD1# signal are ignored while the POWERON signal is active.

3. There is no indicator which shows an activation via DCD interrupt, if DCD1# signal has already

changed from active to inactive during power-on sequence. In other words, if software can not

find activation factor and if the DCDST bit indicates that DCD1# signal is active, the above

situation occurred.

Summary of Contents for VR4181 mPD30181





























































































































































































































































































































































































































































Search results

Summary of Contents for VR4181 mPD30181

Reviews:

Related manuals for VR4181 mPD30181

Brands by name

Popular brands

NEC VR4181 mPD30181, User Manual

Search results

Summary of Contents for VR4181 mPD30181

Reviews:

Related manuals for VR4181 mPD30181

Brands by name

Popular brands