NEC VR4181 mPD30181 User Manual Download Page 78

Page: 78 / 444

CHAPTER 3 CP0 REGISTERS

User’s Manual U14272EJ3V0UM

(1) Interrupt enable

Interrupts are enabled when all of the following conditions are true:

•

IE bit is set to 1.

•

EXL bit is cleared to 0.

•

ERL bit is cleared to 0.

•

The appropriate bit of the IM field is set to 1.

(2) Operating modes

The following Status register bit settings are required for User, Kernel, and Supervisor modes.

•

The processor is in User mode when KSU = 10, EXL = 0, and ERL = 0.

•

The processor is in Supervisor mode when KSU = 01, EXL = 0, and ERL = 0.

•

The processor is in Kernel mode when KSU = 00, EXL = 1, or ERL = 1.

Access to the kernel address space is allowed when the processor is in Kernel mode.

Access to the supervisor address space is allowed when the processor is in Supervisor or Kernel mode.

Access to the user address space is allowed in any of the three operating modes.

(3) Addressing modes

The following Status register bit settings select 32- or 64-bit operation for each of User, Kernel, and Supervisor

operating modes. Enabling 64-bit operation permits the execution of 64-bit opcodes and translation of 64-bit

addresses. 64-bit operation for User, Kernel and Supervisor modes can be set independently.

•

64-bit addressing for Kernel mode is enabled when KX bit = 1. 64-bit operations are always valid in Kernel

mode. If this bit is set, an XTLB Refill exception occurs if a TLB miss occurs in the Kernel mode address

space.

•

64-bit addressing and operations are enabled for Supervisor mode when SX bit = 1. If this bit is set, an

XTLB Refill exception occurs if a TLB miss occurs in the Supervisor mode address space.

•

64-bit addressing and operations are enabled for User mode when UX bit = 1. If this bit is set, an XTLB Refill

exception occurs if a TLB miss occurs in the User mode address space.

(4) Status after reset

The contents of the Status register are undefined after Cold Resets, except for the following bits in the Diagnostic

Status field.

•

TS and SR bits are cleared to 0.

SR bit is 0 after Cold Reset, and is 1 after Soft Reset or NMI.

•

ERL and BEV bits are set to 1.

Remark

Cold Reset and Soft Reset are resets for the CPU core (see 5.3 Reset of CPU Core). For the

reset of all the V

4181 including peripheral units, refer to CHAPTER 5 INITIALIZATION

INTERFACE and CHAPTER 10 POWER MANAGEMENT UNIT (PMU).

Summary of Contents for VR4181 mPD30181





























































































































































































































































































































































































































































Search results

Summary of Contents for VR4181 mPD30181

Reviews:

Related manuals for VR4181 mPD30181

Brands by name

Popular brands

NEC VR4181 mPD30181, User Manual

Search results

Summary of Contents for VR4181 mPD30181

Reviews:

Related manuals for VR4181 mPD30181

Brands by name

Popular brands