manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

The Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN is an advanced automation controller that ensures efficient and seamless communication within industrial systems. Unlock the full potential of this powerful device with our comprehensive user manual, available for free download from manualshive.com. Master this cutting-edge technology with ease.

Share
Download
background image

186

4  TROUBLESHOOTING
4.4  Troubleshooting by Symptom

When "Connection 
Device Information" 
under "Basic Settings" 
of the master station is 
set to "Mixture of CC-
Link IE TSN Class B/A 
or CC-Link IE TSN 
Class A Only"

■

When connected devices are protocol version 2.0

Is the event code 00C80 registered in the event 
history?

Take one of the following actions.

• Check 'Station protocol version 2.0 support status' (SW01A0 to SW01A7) 

and update the firmware of all slave stations to a version that supports the 
protocol version 2.0. Alternatively, replace with slave stations that support 
protocol version 2.0.

• For firmware version "15" or later, set 'Protocol setting' (Un\G1294018) of 

the master station to '1: Protocol version 1.0 fixed'. (

 Page 260 Protocol 

information (Un\G1294016 to Un\G1294031))

• After powering on the slave stations and the devices on the communication 

path, power on the master station.

■

When connected 

devices are protocol 
version 2.0
Is '2: Operating with the 
protocol version 2.0' 
stored in 'Protocol 
operating status' 
(Un\G1294016)?

Is information on 
stations that do not 
support the protocol 
version 2.0 stored in 
'Station protocol version 
2.0 support status' 
(SW01A0 to SW01A7)?

Take one of the following actions.

• Check 'Station protocol version 2.0 support status' (SW01A0 to SW01A7) 

and update the firmware of all slave stations to a version that supports the 
protocol version 2.0. Alternatively, replace with slave stations that support 
protocol version 2.0.

• For firmware version "15" or later, set 'Protocol setting' (Un\G1294018) of 

the master station to '1: Protocol version 1.0 fixed'. (

 Page 260 Protocol 

information (Un\G1294016 to Un\G1294031))

• After powering on the slave stations and the devices on the communication 

path, power on the master station.

■

When connected 

devices are protocol 
version 2.0
Is '1: Operating with the 
protocol version 1.0' 
stored in 'Protocol 
operating status' 
(Un\G1294016)?

Is information on 
stations that do not 
support the protocol 
version 2.0 stored in 
'Station protocol version 
2.0 support status' 
(SW01A0 to SW01A7)?

Check 'Station protocol version 2.0 support status' (SW01A0 to SW01A7) and 
update the firmware of all slave stations to a version that supports the protocol 
version 2.0. Alternatively, replace with slave stations that support protocol 
version 2.0.

Are nine or more CC-
Link IE TSN Class B 
devices and TSN hubs 
connected in total to 
each port of the master 
station in the 
transmission path from 
the master station to the 
CC-Link IE TSN Class 
B device of the end?

Check the connected device and reduce the number of CC-Link IE TSN Class 
B devices and TSN hubs to eight or less in total for each port of the master 
station in the transmission path from the master station to the CC-Link IE TSN 
Class B device of the end.

Has the cyclic data size 
exceeded 2K bytes in 
total for CC-Link IE TSN 
Class A devices 
connected to the CC-
Link IE TSN Class B 
devices other than the 
master station? 
(Including when 
connected to a CC-Link 
IE TSN Class B device 
via a general-purpose 
hub)

• Connect to a CC-Link IE TSN Class B device via a TSN hub. (If connecting 

via a general-purpose hub, change the general-purpose hub to a TSN hub)

• Limit the number of the connected stations so that the cyclic data size of the 

CC-Link IE TSN Class A devices does not exceed 2K bytes in total.

• Connect the CC-Link IE TSN Class A device to the master station.

■

When connected devices are protocol version 2.0

Is there any difference between the CC-Link IE 
TSN Class B/A mixed system configuration and the 
"TSN HUB Setting" in "Connection Device 
Information" under "Basic Settings"?

For details, refer to the following.

Page 201 CC-Link IE TSN Class A device does not perform data link

■

When connected devices are protocol version 2.0

If "CC-Link IE TSN Class Setting" of the general 
CC-Link IE TSN module added to the station list in 
the "CC-Link IE TSN Configuration" window is CC-
Link IE TSN Class A, are the minimum values of 
the communication cycle interval and the cyclic 
transmission time set to "Communication Period 
Interval Setting" and "Cyclic Transmission Time" in 
"Communication Period Setting" under "Basic 
Settings"?

Select the actual device to be used from "Module List" in the "CC-Link IE TSN 
Configuration" window and add it to the list of stations, or refer to the manual 
for the device to be connected to check the maximum response time for the 
time managed polling method and set the calculated values to 
"Communication Period Interval Setting" and "Cyclic Transmission Time".

Is the event code 00C72 registered in the event 
history?

• Update the engineering tool to the latest version.
• Update the slave station firmware with IP address displayed in the detailed 

information of the event history to the latest version.

Check item

Action

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

wattio AIR Read Me preview
AIR
Brand: wattio Pages: 20
Babybee MIO Manual preview
MIO
Brand: Babybee Pages: 28
GE Evolution Series E9000 User Manual preview
Evolution Series E9000
Brand: GE Pages: 44
GE PACSystems RX7i Cpu Programmer'S Reference Manual preview
PACSystems RX7i
Brand: GE Pages: 469
GE GuardSwitch 300 Series Instructions preview
GuardSwitch 300 Series
Brand: GE Pages: 2
GE GuardSwitch 300 Series Instruction preview
GuardSwitch 300 Series
Brand: GE Pages: 2
GE Masoneilan VariPak 28001 Instruction Manual preview
Masoneilan VariPak 28001
Brand: GE Pages: 24
Hankscraft Runxin HD Series Service Manual preview
HD Series
Brand: Hankscraft Runxin Pages: 53
Jafar 3500 Operating Manual preview
3500
Brand: Jafar Pages: 9
Samsung SPC-6000 Quick Setup Manual preview
SPC-6000
Brand: Samsung Pages: 6
Samsung MWR-WE10N Manual preview
MWR-WE10N
Brand: Samsung Pages: 32
Samsung SolarCell Remote Operating Instructions preview
SolarCell Remote
Brand: Samsung Pages: 2
Bartlett 3K Operation Manual preview
3K
Brand: Bartlett Pages: 7
Radionics D9000 Series Installation And Troubleshooting Quick Reference preview
D9000 Series
Brand: Radionics Pages: 14
Daruifuno MCC100 User Manual preview
MCC100
Brand: Daruifuno Pages: 24
IR-Tec OS-NET Programming Manual preview
OS-NET
Brand: IR-Tec Pages: 14
Xylem FLYGT Pareo DCM 711 Installation, Operation And Maintenance Manual preview
FLYGT Pareo DCM 711
Brand: Xylem Pages: 56
HTW HTW-RG66 Owner'S Manual preview
HTW-RG66
Brand: HTW Pages: 88

Brands by name

Popular brands

Load more brands