Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 21 | Manualshive

Page: 21 / 330

background image

1 FUNCTIONS

1.1 Cyclic Transmission

19

1

Communications using RX, RY, RWr, and RWw

This allows data to be exchanged in units of bits and in units of words between the master station and slave station.

Master station and remote stations

■

Unicast mode

1:1 communications between the master station and each remote station. Remote stations do not communicate with each
other.

• Output from the master station

• Input from the remote station

■

Multicast mode

• The master station and remote station send data on the line in multicast mode in each send range.
• The master station receives all data, but the remote station discards the data of another remote station. Therefore,

communication at each station is performed in the same manner as unicast mode. (



Page 19 Unicast mode)

No.0, No.1, No.2: Station No.0 (master station), station No.1, station No.2



No.1,



No.2: Send range: to station No.1, send range: to station No.2



No.1,



No.2: Send range: from station No.1, send range: from station No.2

Class A: CC-Link IE TSN Class A device
Class B: CC-Link IE TSN Class B device



The device of the CPU module turns on.



The device status of the CPU module is stored in the link devices (RY, RWw) of the master station by link refresh.



The status of the link devices (RY, RWw) of the master station is stored in the link devices (RY, RWw) of each remote station by cyclic data transfer
processing.



The status of the link devices (RY, RWw) of the remote station is output to the external device.



The status of the external device is stored in the link devices (RX, RWr) of the remote station.



The status of the link devices (RX, RWr) of the remote station is stored in the link devices (RX, RWr) of the master station by cyclic data transfer processing.



The status of the link devices (RX, RWr) of the master station is stored in the devices of the CPU module by link refresh.

RCPU

X

Y

W

RX

RY

RWr

RWw

0000H

0003H
0004H

0007H

No.1

No.2

0000H

0020H

0000H

001FH

003FH

No.1

No.2

0000H

0003H
0004H

007FH

No.1

No.2

0000H

001FH
0020H

003FH

No.1

No.2

Ø

Ø

Ó

Ó

Ö

Õ

RX

RY

RWr

RWw

No.2

No.2

No.2

No.2

RX

RY

RWr

RWw

0000H

0003H

No.1

0000H

001FH

No.1

0000H

0003H

No.1

0000H

001FH

0000H

0003H

0000H

001FH

0000H

0003H

0000H

001FH

No.1

Ô

×

No.2

No.1

No.0

END

Ò

Class B

Class B

Class A

«
...
19
20
21
22
23
...
»

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Brand: ABB Pages: 2

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: CALEFFI Pages: 12

QuickSetter+ 132 Series

Brand: CALEFFI Pages: 5

Brand: tams elektronik Pages: 60

GRAVIMETRIC AUGER FEEDER MGF-ST

Brand: Maguire Products Pages: 47

Brand: Magtrol Pages: 160

FOUNDATION 3730-5

Brand: Samson Pages: 132

Brand: Samson Pages: 68

Brand: Samson Pages: 128

Brand: Samson Pages: 68

Brand: X-POWER Pages: 24

Brand: Samson Pages: 80

Brand: Haehne Pages: 44

Brand: Jäger Pages: 18

Brand: DSEGenset Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands