manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 316

314

APPX
Appendix 7  Processing Time

Monitoring time for safety communications

This section describes the monitoring time for the safety communications.
The monitoring time is set for each safety connection. If the time exceeds the monitoring time, a safety communication 
timeout is detected and the safety communications are stopped.

*1 The safety refresh monitoring time uses a common value between the master station and slave stations.

Setting 
station

Item

Description

Station using 
setting time

Master 
station

Transmission Interval 
Monitoring Time

• A slave station monitors the transmission interval 

 that the master station sends 

safety data.

• The master station sends data to the slave station at the start of the safety 

communications.

• The safety data includes the information of the time at which the data was sent. 

The slave station monitors the transmission interval by comparing the time 
information with the previous time information.

Slave station

Safety Refresh Monitoring 
Time

*1

The master station monitors the receiving interval 

 that safety data received from a 

slave station.

Master station

• A slave station monitors the receiving interval 

 that safety data received from the 

master station.

• The master station sends data to the slave station at the start of the safety 

communications.

Slave station

Slave station

Transmission Interval 
Monitoring Time

• The master station monitors the transmission interval 

 that a slave station sends 

safety data.

• A slave station sends data to the master station at starting the safety 

communications.

• The transmission time information with safety data received on the master station 

is monitored as compared with the last value.

Master station

(1) Safety data sent from the master station to a slave station
(2) Safety data sent from a slave station to the master station

 to 

: Transmission/receiving intervals of safety data

Ò

Ó

Ô

Õ

(1)

(2)

Master station

Slave station

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands