Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 34 | Manualshive

Page: 34 / 330

background image

32

1 FUNCTIONS
1.1 Cyclic Transmission

Readable and writable range

Data can be read or written from/to the RJ71GN11-T2 on the base unit where the CPU module is mounted.

■

Read

All link devices of the RJ71GN11-T2 can be specified. (



Page 31 Specification method)

■

Write

The range that satisfies all of the following conditions can be specified.
• Area where data is sent to other stations and outside the link refresh range (



Page 19 Communications using RX, RY,

• Within the link device range of the RJ71GN11-T2 (



Page 31 Specification method)

Ex.

(1) Out of the link refresh range (Data can be written here.)
(2) Area where data is sent to other stations
(3) Area for receiving data from other stations

(2)

(1)

(3)

Y

RY

RJ71GN11-T2

CPU module

Link refresh

Link refresh

«
...
32
33
34
35
36
...
»

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Brand: Balboa Pages: 12

Brand: Paoli Pages: 16

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Samsung Pages: 20

Brand: 1Control Pages: 8

Brand: Dantherm Pages: 96

Brand: Abicor Binzel Pages: 8

Brand: Samson Pages: 32

Brand: Quantum Pages: 15

Brand: Parker Pages: 28

Brand: Watlow Pages: 4

Brand: Bartlett Pages: 7

Brand: Balboa Water Group Pages: 88

Brand: ABB Pages: 2

Brand: Nemesis Pages: 6

TBEN-L 8IOL Series

Brand: turck Pages: 148

APEXpy 07-37A2-2111/ 520Series

Brand: Bartec Pages: 98

Brand: Reer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands