Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 39 | Manualshive

Page: 39 / 330

background image

1 FUNCTIONS

1.1 Cyclic Transmission

37

1

• Program
Sending station: Master station (station No.0)

Receiving station: Local station (station No.1)

• Program flow

Classification

Setting details

Label to be defined

Define global labels as shown below:

Classification

Setting details

Label to be defined

Define global labels as shown below:



The master station checks that the send request bStartDirection (M0) is turned on, and transfers contents of uTransferFrom [0] to [3] (D0 to D3) to the send
data W0 to W3.



When the transfer is completed, the master station turns on Y1000.



The local station checks that X1000 is turned on, and transfers contents of the receive data W1000 to W1003 to uTransferTo [0] to [3] (D0 to D3).



When the transfer is completed, the local station turns on Y1000.



The master station checks that X1000 is turned on, and turns off Y1000.



The local station checks that X1000 is turned off, and turns off the reception complete signal Y1000.

«
...
37
38
39
40
41
...
»

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Brand: FAAC Pages: 14

Brand: Walchem Pages: 10

Brand: Echelon Pages: 40

Brand: H3C Pages: 5

Brand: H3C Pages: 27

Brand: H3C Pages: 4

Brand: H3C Pages: 54

Brand: H3C Pages: 10

Brand: H3C Pages: 10

Brand: KEENZ Pages: 68

Brand: Jetter Pages: 24

Brand: Gemini Pages: 9

Brand: M-system Pages: 18

Brand: Wilo Pages: 128

Brand: Simplex Pages: 78

Brand: Vega Pages: 28

Brand: WATSON Pages: 16

Brand: Danfoss Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands