Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 43 | Manualshive

Page: 43 / 330

background image

1 FUNCTIONS

1.1 Cyclic Transmission

41

1

Receiving station: Local station (station No.1)

• Program flow

Classification

Setting details

Label to be defined

Define global labels as shown below:



The master station checks that the send request bStartDirection (M0) is turned on, and transfers contents of uOutputData [0] to [3] to the send data W0 to
W3.



When the transfer is completed, the master station turns on B0.



The local station checks that B0 is turned on, and transfers contents of the receive data W0 to W3 to uInputData [0] to [3] (D100 to D103).



When the transfer is completed, the local station turns on B100.



The master station checks that B100 is turned on, and turns off B0.



The local station checks that B0 is turned off, and turns off B100.

«
...
41
42
43
44
45
...
»

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Brand: Valve Concepts Pages: 16

Brand: FAAC Pages: 14

Brand: Ickle Bubba Pages: 23

Brand: XGAMING Pages: 9

medialon Showmaster Go

Brand: 7th Sense Pages: 2

Brand: Jafar Pages: 10

Brand: Calsense Pages: 74

Brand: jbc Pages: 4

Brand: jbc Pages: 4

Brand: VAT Pages: 39

Brand: Samson Pages: 124

Brand: Samson Pages: 86

Brand: VAC Pages: 5

Brand: UniPOS Pages: 51

Brand: Unipulse Pages: 126

Brand: YachtSafe Pages: 3

Brand: Tylo Pages: 51

Cutler-Hammer LMR

Brand: Eaton Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands