manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

The Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN is an advanced automation controller that ensures efficient and seamless communication within industrial systems. Unlock the full potential of this powerful device with our comprehensive user manual, available for free download from manualshive.com. Master this cutting-edge technology with ease.

Share
Download
background image

4  TROUBLESHOOTING

4.5  List of Error Codes

223

4

D25FH

A remote instruction was executed from the 
module with a station type which cannot 
execute it.

Stations other than the master station cannot execute a remote instruction. 
Modify the program so that remote instructions are not executed from 
stations that cannot use them.

D260H

A remote instruction was executed from the 
module with a station type which cannot 
execute it.

Stations other than the master station cannot execute a remote instruction. 
Modify the program so that remote instructions are not executed from 
stations that cannot use them.

D262H

The total number of slave stations specified 
in the CCPASET instruction is incorrect.

• Execute the instruction again after correcting the total number of slave 

stations in the control data.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D263H

The constant link scan time setting of the 
CCPASET instruction is incorrect.

• Execute the instruction again after correcting the constant link scan time 

in the control data.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D264H

The station number setting of the CCPASET 
instruction is incorrect.

• Execute the instruction again after correcting the station number in the 

network configuration setting data so it is within 1 to 120.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D265H

The station number specified for the 
CCPASET instruction is already in use.

• Execute the instruction again after correcting the station number in the 

network configuration setting data to a unique value.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D266H

The number of occupied stations specified in 
the CCPASET instruction is incorrect.

• Execute the instruction again after correcting the number of occupied 

stations in the network configuration setting data.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D267H

The station type of the CCPASET instruction 
is incorrect.

• Execute the instruction again after correcting the station type in the 

network configuration setting data.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D268H

The link device range assignment specified 
for each station in the CCPASET instruction 
is incorrect.

• Execute the instruction again after correcting the offset or the number of 

points of link devices in the network configuration setting data.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D269H

The station type of the REMFR/REMTO/
REMFRD/REMTOD/REMFRIP/REMFRDIP/
REMTOIP/REMTODIP instruction target 
station is not a remote station.

• Set the station type of the REMFR/REMTO/REMFRD/REMTOD/

REMFRIP/REMFRDIP/REMTOIP/REMTODIP instruction target station to 
a remote station.

• Correct the network number and station number/IP address of the target 

station of the dedicated instruction.

D26AH

The target station of the REMFR/REMTO/
REMFRD/REMTOD/REMFRIP/REMFRDIP/
REMTOIP/REMTODIP instruction does not 
exist.

If the target station of the REMFR/REMTO/REMFRD/REMTOD/REMFRIP/
REMFRDIP/REMTOIP/REMTODIP instruction is disconnected, execute the 
dedicated instruction again after return of the target station.

D26BH

The network number setting of the 
CCPASET instruction executing station is 
incorrect.

Set "Network No." under "Network No." of "Required Settings" to between 1 
and 239.

D26CH

The station type and station number of the 
CCPASET instruction executing station are 
incorrect.

Rewrite the module parameter using the engineering tool. If the same error 
occurs again even after taking the above, the possible cause is a hardware 
failure of the error module. Please consult your local Mitsubishi 
representative.

D273H

The request data size of transient 
transmission is incorrect.

• Correct the request command at the transient request source, and retry 

the operation.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D275H

Other dedicated instructions are in 
execution, and the executed instruction 
cannot be processed.

• Execute the instruction again after a while.
• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D27AH

The own station number set in the UINI 
instruction is incorrect.

• Set the station number of the own station in the control data to a value 

from 1 to 120, and retry the operation.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

Error 
code

Error definition and causes

Action

Detailed 
information 1

Detailed 
information 2

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

GBD SC Series Electrical Connections preview
SC Series
Brand: GBD Pages: 12
EasyIO FG Series User Manual preview
FG Series
Brand: EasyIO Pages: 12
RMG GSM 3ST User Manual preview
GSM 3ST
Brand: RMG Pages: 6
Unitech RM300 SDK User Manual preview
RM300 SDK
Brand: Unitech Pages: 11
B meters IWM-PL4 Quick User Manual preview
IWM-PL4
Brand: B meters Pages: 10
IDS X64 Manual preview
X64
Brand: IDS Pages: 2
Jabra LINK 280 - User Manual preview
LINK 280 -
Brand: Jabra Pages: 8
Omnex R1300 Manual preview
R1300
Brand: Omnex Pages: 9
Omegon MiniTrack LX2 Instruction Manual preview
MiniTrack LX2
Brand: Omegon Pages: 6
WATERLOO Smart Panel Owner'S Manual preview
Smart Panel
Brand: WATERLOO Pages: 8
Paradox REM3 Instructions preview
REM3
Brand: Paradox Pages: 2
Paradox MG-RCV3 Reference & Installation Manual preview
MG-RCV3
Brand: Paradox Pages: 44
Parker A4W Series Installation And Service Information preview
A4W Series
Brand: Parker Pages: 12
RAKwireless RAK3172 User Manual preview
RAK3172
Brand: RAKwireless Pages: 6
Watts 709 Series Instruction, Installation, Maintenance And Repair Manual preview
709 Series
Brand: Watts Pages: 4
WaterCop SmartConnect Owner'S Manual preview
SmartConnect
Brand: WaterCop Pages: 4
V2 WES-EASY Manual preview
WES-EASY
Brand: V2 Pages: 48
Festo CPX-AP-A-16DI-D-M12-5P Operating Instructions Manual preview
CPX-AP-A-16DI-D-M12-5P
Brand: Festo Pages: 16

Brands by name

Popular brands

Load more brands