manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 102

100

2  PARAMETER SETTINGS
2.3  Basic Settings

The link devices of the RJ71GN11-T2 can be accessed from a program. (

 Page 31 Direct access to link 

devices)

1 to 256

Link Side

Set the link refresh ranges of link devices (RX, RY, RWr, RWw, LB, LW). 
Up to 256 ranges can be set. (

 Page 29 Link refresh)

■

Device Name

• RX, RY, RWr, RWw, LB, LW

(Default: empty)

■

Points

• RX, RY: 16 to 16384
• RWr, RWw: 4 to 8192
• LB: 16 to 32768
• LW: 1 to 16384

(Default: Grayout)

■

Start

• RX, RY: 0H to 3FF0H (set in increments of 16 points)
• RWr, RWw: 0H to 1FFCH (set in increments of 4 points)
• LB: 0H to 7FF0H (set in increments of 16 points)
• LW: 0H to 3FFFH

(Default: Grayout)

■

End

• RX, RY: FH to 3FFFH (set in increments of 16 points)
• RWr, RWw: 3H to 1FFFH (set in increments of 4 points)
• LB: FH to 7FFFH (set in increments of 16 points)
• LW: 0H to 3FFFH

(Default: Grayout)

CPU Side

■

Target

• Module Label
• Specify Device

(Default: Grayout)

■

Device Name

• Specify Device (link side is RX): X, M, L, B, D, W, R, ZR, 

RD

• Specify Device (link side is RY): Y, M, L, B, D, W, R, ZR, 

RD

• Specify Device (link side is RWr, RWw): M, L, B, D, W, 

R, ZR, RD

• Specify Device (link side is LB, LW): X, Y, M, L, B, D, W, 

R, ZR, RD

(Default: Grayout)

■

Points, End

• Module Label: 

• Specify Device: Displayed according to setting of 

"Start".

(Default: Grayout)

■

Start

• Module Label: 

• Specify Device: Device range of CPU modules (Set bit 

devices in increments of 16 points and word devices in 
increments of 4 points.)

(Default: Grayout)

Item

Description

Setting range

00000H

000FFH

00000H

0001FH

01000H

010FFH

00000H

003FFH

01000H

013FFH

00000H

00013H

00000H

00013H

00100H

0011FH

RJ71GN11-T2

RCPU

No.1

No.2

No.3

No.4

00100H

001FFH

00000H

000FFH

00100H

001FFH

00200H

002FFH

·

·

·

·

·

·

·

·

·

·

·

·

LB

LW

B

W

W

W

Y

X

RWw

RWr

RY

RX

Ex.

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands