Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 265

Page: 265 / 330

APPX

Appendix 3 Buffer Memory

263

Connection status storage area

■

Latest error code after the 2nd connection of MELSOFT transmission port (TCP/IP)

(Un\G2097380 to Un\G2097386)

The latest error code of the 2nd to 8th connection of the MELSOFT transmission port (TCP/IP) is stored.

■

Latest error code after the 2nd connection of SLMP transmission port (TCP/IP) (Un\G2097508

to Un\G2097514)

The latest error code of the 2nd to 8th connection of the SLMP transmission port (TCP/IP) is stored.

System port latest error code storage area

■

Auto-open UDP port latest error code (Un\G2098154)

The latest error code of the auto-open UDP port is stored.

■

MELSOFT transmission port (UDP/IP) latest error code (Un\G2098155)

The latest error code of the MELSOFT transmission port (UDP/IP) is stored.

■

MELSOFT transmission port (TCP/IP) latest error code (Un\G2098156)

The latest error code of the MELSOFT transmission port (TCP/IP) is stored.

■

SLMP transmission port (UDP/IP) latest error code (Un\G2098157)

The latest error code of the SLMP transmission port (UDP/IP) is stored.

■

SLMP transmission port (TCP/IP) latest error code (Un\G2098158)

The latest error code of the SLMP transmission port (TCP/IP) is stored.

■

SLMPSND instruction latest error code (Un\G2098159)

The latest error code of the SLMPSND instruction is stored.

Status for each protocol (IP packet)

■

Received packet total count (Un\G2102152 to Un\G2102153, Un\G4199304 to Un\G4199305)

The status is counted from 0 to 4294967295 (FFFFFFFFH).

■

Received packet checksum error discard count (Un\G2102154 to Un\G2102155, Un\G4199306

to Un\G4199307)

The status is counted from 0 to 4294967295 (FFFFFFFFH).

■

Sent packet total count (Un\G2102156 to Un\G2102157, Un\G4199308 to Un\G4199309)

The status is counted from 0 to 4294967295 (FFFFFFFFH).

■

Simultaneous transmission error detection count (receive buffer full count) (Un\G2102174 to

Un\G2102175, Un\G4199326 to Un\G4199327)

The status is counted from 0 to 4294967295 (FFFFFFFFH).

■

Receive abort count (Un\G2102181, Un\G4199333)

The status is counted from 0 to 65535 (FFFFH).

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Search results

Summary of Contents for MELSEC iQ-R CC-Link IE TSN

Reviews:

Brands by name

Popular brands

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Search results

Summary of Contents for MELSEC iQ-R CC-Link IE TSN

Reviews:

Brands by name

Popular brands