manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 79

1  FUNCTIONS

1.6  CC-Link IE TSN Network Synchronous Communication Function

77

1

Setting method

For the setting method, refer to the following manual.

 MELSEC iQ-R Inter-Module Synchronization Function Reference Manual

■

Inter-module synchronization cycle

To use the CC-Link IE TSN network synchronous communication function, set the same cycle for the following two items.
 • "Fixed Scan Interval Setting" under "Inter-module Synchronization Setting" in "System Parameter".
 • "Communication Period Interval Setting" under "Basic Settings" of the module parameter
Set the cycle in the following range.
0.25 to 10.0ms (in units of 0.05ms)

■

How to calculate an inter-module synchronization cycle

For the cycle to be set, set a value greater than a value obtained by one of the following formulas.

*1 For the values obtained by the calculation formulas, refer to the following.

Execution time of the inter-module synchronous interrupt program (I44) (

 User's manual of the CPU module used)

Cyclic transmission time and cyclic processing time (

 Page 293 Communication cycle intervals)

Precautions

To use the CC-Link IE TSN network synchronous communication function, do not set "Not Set" for "0.05ms Unit Setting" of 
"Fixed Scan Interval Setting of Inter-module Synchronization" in "System parameter".
None of the inter-module synchronization cycles 0.222ms, 0.444ms, 0.888ms, 1.777ms, 3.555ms, and 7.111ms can be used 
by the CC-Link IE TSN network synchronous communication function. Therefore, neither the SSCNET/H supported Simple 
Motion module nor Motion CPU can synchronize with the inter-module synchronization cycle.

Condition

Calculation formula

*1

Execution time of the inter-module synchronous interrupt program (I44) > 
cyclic transmission time

Execution time of the inter-module synchronous interrupt program (I44) + 
cyclic processing time

Execution time of the inter-module synchronous interrupt program (I44) 

 

cyclic transmission time

Cyclic transmission time + cyclic processing time

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands