manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

The Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN is an advanced automation controller that ensures efficient and seamless communication within industrial systems. Unlock the full potential of this powerful device with our comprehensive user manual, available for free download from manualshive.com. Master this cutting-edge technology with ease.

Share
Download
background image

206

4  TROUBLESHOOTING
4.5  List of Error Codes

1845H

Too much processing of transient 
transmission (link dedicated instruction) and 
cannot perform transient transmission.

Correct the transient transmission (link dedicated instruction) execution 
count.

1D10H

Cyclic transmission skip occurred.

• Increase the value for the inter-module synchronization cycle set in "Fixed 

Scan Interval Setting of Inter-module Synchronization" under "Inter-
module Synchronization Setting" in "System Parameter" so that the 
execution time of synchronization interrupt program does not exceed the 
inter-module synchronization cycle.

• Increase the value for " Communication Period Interval Setting" and 

"Transient Transmission Time" in " Communication Period Setting" of the 
module parameter.

• If the value is not 0 in 'Transient transmission additional time (calculation 

value)' (SW007A), add the value to "Communication Period Interval 
Setting" and "Transient Transmission Time".

• Reduce the program processing time by reducing the program volume so 

that the execution time of synchronization interrupt program does not 
exceed the inter-module synchronization cycle.

• Reduce the refresh processing time by reducing the data targeted for 

synchronization refreshing so that the execution time of synchronization 
interrupt program does not exceed the inter-module synchronization 
cycle.

• Set modules not requiring synchronization to asynchronous so that the 

execution time of synchronization interrupt program does not exceed the 
inter-module synchronization cycle.

• Do not perform the online change in the CPU module.

1D11H

The correction value of time counter 
calculated by the inter-module 
synchronization function exceeds allowable 
range.

• Take measures to reduce noise.
• If the same error occurs a few times even after taking the above, the 

possible cause is a hardware failure of the module or base unit. Please 
consult your local Mitsubishi representative.

1D20H

The module cannot normally communicate 
with the slave station on CC-Link IE TSN.

• To use the inter-module synchronization function, set the setting value for 

the inter-module synchronization cycle longer than the current setting in 
"Inter-module Synchronization Setting" under "Inter-module 
Synchronization Setting" in "System Parameter".

• Make the setting value greater than the current setting for 

"Communication Period Interval Setting" and "Transient Transmission 
Time" in "Communication Period Setting" of the module parameter.

• If the value is not 0 in 'Transient transmission additional time (calculation 

value)' (SW007A), add the value to "Communication Period Interval 
Setting" and "Transient Transmission Time".

• Refer to the manual for the slave stations used and if they do not support 

the communication cycle of "Normal-Speed" and "Low-Speed", set 
"Network Configuration Setting" to "Basic Period" under "Basic Settings" 
of the master station.

• Do not perform the online change in the CPU module.
• Check if the switching hub and the cables are connected properly.
• After taking the above actions, power on the system again or reset the 

CPU module.

■

■

Target station 

information

• Network No.
• Station No.
• IP address

1D21H

Initialization processing with the slave station 
on CC-Link IE TSN cannot be performed 
correctly.

• Update the version of the station shown in detailed information 2 to the 

one that supports the CC-Link IE TSN network synchronous 
communication function.

• Take measures to reduce noise.
• After taking the above actions, power on the system again or reset the 

CPU module.

■

■

Target station 

information

• Network No.
• Station No.
• IP address

1D30H

A co-recording trigger was received but then 
discarded because the trigger was not 
supported.

Check the firmware versions of the network module and the co-recording 
trigger source device. If the combination is incorrect, update the firmware 
version of the network module or co-recording trigger source device, 
whichever the older version is used.

■

Source 

information

• I/O No.
• Network No.
• Station No.
• IP address

■

20E0H

The module cannot communicate with the 
CPU module.

The hardware failure of the CPU module may have been occurred. Please 
consult your local Mitsubishi representative.

2160H

IP address duplication was detected.

Check and correct the IP addresses.

Error 
code

Error definition and causes

Action

Detailed 
information 1

Detailed 
information 2

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Nelson 800 Series Application Manual preview
800 Series
Brand: Nelson Pages: 19
C-TEC 800 Series Installation Instructions preview
800 Series
Brand: C-TEC Pages: 2
ABATEC A1 Installation And Operation Instruction Manual preview
A1
Brand: ABATEC Pages: 8
M&C 701 Instruction Manual preview
701
Brand: M&C Pages: 16
DAB ACTIVE DRIVER M/M 1.1 Programming Manual preview
ACTIVE DRIVER M/M 1.1
Brand: DAB Pages: 10
d&b audiotechnik 10D Quick Start Manual preview
10D
Brand: d&b audiotechnik Pages: 3
DAB PUMPS ACTIVE DRIVER M/M 1.1 Manual preview
ACTIVE DRIVER M/M 1.1
Brand: DAB PUMPS Pages: 38
Federal Signal Corporation ultravoice UV Installation, Operation And Service Manual preview
ultravoice UV
Brand: Federal Signal Corporation Pages: 79
Federal Signal Corporation PAGASYS GEN II Description, Installation, And User Manual preview
PAGASYS GEN II
Brand: Federal Signal Corporation Pages: 32
Maclaren Major Elite Manual preview
Major Elite
Brand: Maclaren Pages: 43
Lawler 804 Installation & Maintenance Manual preview
804
Brand: Lawler Pages: 5
B&G ZEUS S Detailed App Manual preview
ZEUS S
Brand: B&G Pages: 19
POLA HP49 Handbook preview
HP49
Brand: POLA Pages: 2
Reer MOSAIC MA2 Quick Installation Manual preview
MOSAIC MA2
Brand: Reer Pages: 2
Jeckson Electric 47-1010A-T Owner'S Manual preview
47-1010A-T
Brand: Jeckson Electric Pages: 2
Sunlover SL6 ELITE Quick Start Manual preview
SL6 ELITE
Brand: Sunlover Pages: 2
Flying Industry Development S1PF-DC12 Quick Manual preview
S1PF-DC12
Brand: Flying Industry Development Pages: 2
G-Tech FIELD MATE User Manual And Installation Manual preview
FIELD MATE
Brand: G-Tech Pages: 26

Brands by name

Popular brands

Load more brands