manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 134

132

3  PROGRAMMING
3.1  Precautions for Programming

3

PROGRAMMING

This chapter describes programming and startup examples of CC-Link IE TSN.

3.1

Precautions for Programming

This section describes precautions to create CC-Link IE TSN programs.

Cyclic transmission program

For a cyclic transmission program, configure an interlock with the following module labels (link special relay (SB), link special 
register (SW)).
 • 'Data link error status of own station' (SB0049)
 • 'Data link status of each station' (SW00B0 to SW00B7)

Program using safety communications

For a program using safety communications, interlock with the safety special register described below. (For the 1st master/
local module)
 • 'Safety refresh communication status of each safety connection (1st module)' (SA\SD1008 to SA\SD1015)
For a communication example using the safety communications, refer to the following.
 • Communication Example of Safety Communications (

 Page 145 Communication Example of Safety Communication)

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands