manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

The Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN is an advanced automation controller that ensures efficient and seamless communication within industrial systems. Unlock the full potential of this powerful device with our comprehensive user manual, available for free download from manualshive.com. Master this cutting-edge technology with ease.

Share
Download
background image

230

4  TROUBLESHOOTING
4.5  List of Error Codes

D843H

The module operation mode is set to a mode 
in which transient transmission cannot be 
executed.

After completion of the module communication test, retry the transient 
transmission.

D844H

Incorrect frame was received.

• Unsupported pre-conversion protocol
• Unsupported frame type
• Application header variable part
• Application header HDS
• Application header RTP
• Read command not requiring response

Execute the instruction again after correcting the request data at the 
transient request source.

D902H

The online test data is incorrect.

• Correct the data at the station that started the online test, and retry the 

operation.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D903H

During execution of the communication test, 
the test was retried.

After completion of the communication test, retry the operation.

D905H

A communication monitoring timeout has 
occurred in communication test.

• Check the network status using the CC-Link IE TSN/CC-Link IE Field 

diagnostics of the engineering tool, and take action. Then, retry the 
operation.

• Check if "Routing Setting" of "CPU Parameter" is correctly set, and take 

action.

D906H

Transmission completion wait timeout has 
occurred in communication test.

• Check the network status using the CC-Link IE TSN/CC-Link IE Field 

diagnostics of the engineering tool, and take action. Then, retry the 
operation.

• Execute the instruction again after lower the transient transmission usage 

frequency.

• Check if "Routing Setting" of "CPU Parameter" is correctly set, and take 

action.

D909H

The header information of transient 
transmission is incorrect.

Execute the instruction again after correcting the header information at the 
transient request source.

D90AH

During execution of the communication test, 
the test was retried.

Check the network status using the CC-Link IE TSN/CC-Link IE Field 
diagnostics of the engineering tool, and take action. Then, retry the 
operation.

D90BH

The number of stations that communicate in 
the network is out of the specification range.

• Check the network status using the CC-Link IE TSN/CC-Link IE Field 

diagnostics of the engineering tool, and take action.

• If the number of slave stations per network is more than 120, reduce it to 

120 or less.

D90CH

The communication destination specified for 
the communication test is incorrect.

• Correct "Target Station" of communication test, and retry the operation.
• "Communication Test" cannot be executed for own station and relay 

sending station. Set "Target Station" to other than own station and relay 
transmission station.

• The target station is mounted on the same base unit (main base unit and 

extension base unit) as the connected station (own station). Do not 
execute the communication test for station on the same base unit (main 
base unit and extension base unit) as the connected station (own station).

D90DH

An error was detected in the network 
module.

Please consult your local Mitsubishi representative.

D912H

Transient transmission sending failed.

• Execute the instruction again after lower the transient transmission usage 

frequency.

• Check if the switching hub and the Ethernet cables are connected 

properly.

D913H 
to 
D917H

An error was detected in the network 
module.

Please consult your local Mitsubishi representative.

D919H

No response from the target station of the 
communication test.

• Correct the network number, station number, or IP address for the target 

station of the communication test.

• Check if the network configuration setting is correctly set in the master 

station within the same network as the target station of the communication 
test.

• When "IP Address" is selected for "Communication Method", 

"Communication Test" cannot be executed for stations on networks 
different from that of the connected station (own station). Change 
"Communication Method" to "Network No./Station No.".

Error 
code

Error definition and causes

Action

Detailed 
information 1

Detailed 
information 2

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Nidec Leroy-Somer R180 Installation And Maintenance Manual preview
Leroy-Somer R180
Brand: Nidec Pages: 20
GE TLE Scalable 150 Quick Start Manual preview
TLE Scalable 150
Brand: GE Pages: 6
GE SIMON XT Instruction Manual preview
SIMON XT
Brand: GE Pages: 3
GE NetworX Series Installation And Start-Up Manual preview
NetworX Series
Brand: GE Pages: 80
GE PACSystems* RX3i Application Manual preview
PACSystems* RX3i
Brand: GE Pages: 39
GE PACSystems* RX3i Secure Deployment Manual preview
PACSystems* RX3i
Brand: GE Pages: 35
GE PACSystems* RX3i Important Product Information preview
PACSystems* RX3i
Brand: GE Pages: 3
GE PACSystems* RX3i User Manual preview
PACSystems* RX3i
Brand: GE Pages: 169
GE PACSystems RX7i Reference Manual preview
PACSystems RX7i
Brand: GE Pages: 317
YASKAWA U1000 iQpump Drive Quick Start Quide preview
U1000 iQpump Drive
Brand: YASKAWA Pages: 26
YASKAWA Z1000 CIMR-ZU*A Series Quick Start Up Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 2
YASKAWA SIEMENS CNC Series Maintenance Manual, Serviceman Handbook preview
CNC Series
Brand: YASKAWA SIEMENS Pages: 373
Ziton ZP1-X3E Series Operation Manual preview
ZP1-X3E Series
Brand: Ziton Pages: 36
HW Group HWg-SH3 Manual preview
HWg-SH3
Brand: HW Group Pages: 18
oventrop 2104203 Operating Instructions Manual preview
2104203
Brand: oventrop Pages: 64
LCT HQ-TJ-901 Operation Manual preview
HQ-TJ-901
Brand: LCT Pages: 5
Velux KUX 100 Instructions Manual preview
KUX 100
Brand: Velux Pages: 11
Kantronics KAM XL Reference Manual preview
KAM XL
Brand: Kantronics Pages: 201

Brands by name

Popular brands

Load more brands