manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 218

216

4  TROUBLESHOOTING
4.5  List of Error Codes

C053H

The number of read/write points from/to the 
random device of SLMP message is out of 
the allowable range in the CPU module (in 
units of bits).

Correct the number of read/write points and send the SLMP message to the 
CC-Link IE TSN-equipped module again.

C054H

The number of read/write points from/to the 
random device of SLMP message is out of 
the allowable range in the CPU module (in 
units of words, double words).

Correct the number of read/write points and send the SLMP message to the 
CC-Link IE TSN-equipped module again.

C055H

The read/write size from/to the file data of 
SLMP message is out of the allowable 
range.

Correct the read/write size send the SLMP message to the CC-Link IE TSN-
equipped module again.

C056H

The read/write request exceeds the largest 
address.

• Correct the start address or the number of read/write points so that the 

request does not exceed the largest address and send the data to the CC-
Link IE TSN-equipped module again.

• If the access target and connection stations are modules of the MELSEC 

iQ-R series, send the SLMP message again to the CC-Link IE TSN-
equipped module using 00

3 and 00

2 of subcommands.

C057H

The request data length of the SLMP 
message does not match the number of data 
in the character (a part of text).

Check and correct the text or request data length, and send the SLMP 
message to the CC-Link IE TSN-equipped module again.

C058H

The request data length of the SLMP 
message after the ASCII/binary conversion 
does not match with the number of data in 
the character (a part of text).

Check and correct the text or request data length, and send the SLMP 
message to the CC-Link IE TSN-equipped module again.

C059H

• The specified command and subcommand 

of the SLMP message are incorrect

• A function that is not supported by the 

target device was executed.

• Check that there are no errors in the specification of the command and 

subcommand of the SLMP message.

• Check whether the function executed is supported by the target device.
• Check the version of the target device.

C05AH

The CC-Link IE TSN-equipped module 
cannot read/write data from/to the device 
specified by the SLMP message.

Correct the specification of the device to be read/written and send the SLMP 
message to the CC-Link IE TSN-equipped module again.

C05BH

The CC-Link IE TSN-equipped module 
cannot read/write data from/to the device 
specified by the SLMP message.

Correct the specification of the device to be read/written and send the SLMP 
message to the CC-Link IE TSN-equipped module again.

C05CH

The received request data of the SLMP 
message is incorrect.

Correct the request data and send the SLMP message to the CC-Link IE 
TSN-equipped module again.

C05DH

The "Monitor Request" command is received 
before the monitor registration is performed 
by the "Monitor Registration/Clear" 
command of the SLMP message.

Register the monitoring data using "Monitor Registration/Clear" command 
and perform monitoring.

C05EH

• The time between reception of the SLMP 

message by the CC-Link IE TSN-
equipped module and the returned 
response from the access destination 
exceeded the monitoring timer value set in 
the SLMP command.

• An unresponsive command was sent to 

another network station as the access 
destination. (If this error does not cause 
any problems, it can be ignored.)

• Increase the monitoring timer value.
• Check if the access destination is operating normally.
• Correct the network number or request destination station number.
• If the access destination is a module with a different network number, 

correct the routing parameter setting.

• If the access destination is a module with a different network number, 

check if the network number is not in use.

C05FH

This request cannot be executed to the 
access destination specified by the SLMP 
message.

Correct the access destination.

C060H

The request details for bit devices of the 
SLMP message is incorrect.

Correct the request details and send the SLMP message to the CC-Link IE 
TSN-equipped module again.

C061H

• The request data length of the SLMP 

message does not match the number of 
data in the character (a part of text).

• The write data length specified by the 

label write command is not even byte.

• Check and correct the text or request data length, and send the SLMP 

message to the CC-Link IE TSN-equipped module again.

• Add one byte of dummy data, and specify the length as an even number 

of bytes.

Error 
code

Error definition and causes

Action

Detailed 
information 1

Detailed 
information 2

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands