Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 162 | Manualshive

Page: 162 / 330

background image

160

3 PROGRAMMING
3.3 Communication Example of Safety Communication

Local station (station No.1)

■

Local station (station No.1)

Classification

Device

Description

Safety special register

SA\SD1008.0

Safety refresh communication status of each safety connection (1st module) (safety
connection No.1)

SA\SD1232.0

Interlock status of each safety connection (1st module) (safety connection No.1)

SA\SD1240.0

Interlock release request for each safety connection (1st module) (safety connection
No.1)

Label to be defined

Define safety global labels as shown below:

(0) Processing to release the safety station interlock status in safety communications with station No.0 (master station) Turning on bResetSwitch, the safety

station interlock status with safety connection No.1 is released.

(6) Communication program with station No.0 (master station) When the safety station interlock status with station No.1 is normal and bOtherSafeState is on,

safety output data is sent to the station No.0 by turning on bSendSafeDataStationNo0. bRecvSafeDataStationNo0 is also turned on when safety input data
is received from the station No.0.

«
...
160
161
162
163
164
...
»

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Brand: ZETRON Pages: 3

Brand: ADEMCO Pages: 2

Brand: MacDon Pages: 32

Brand: K&K Pages: 6

GRAVIMETRIC AUGER FEEDER MGF-ST

Brand: Maguire Products Pages: 47

Brand: Magtrol Pages: 160

Brand: Talgil Pages: 14

Brand: Tadao Pages: 2

Brand: Vaillant Pages: 12

Brand: Klimaire Pages: 5

SaunaLogic SL2 Control

Brand: Finnleo Pages: 14

Brand: IR-Tec Pages: 14

Brand: IDEATEC Pages: 32

Brand: Broadcast Tools Pages: 15

Brand: Quickie Pages: 64

Brand: Kamstrup Pages: 7

Brand: Radionics Pages: 18

Brand: Renogy Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands