manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 68

66

1  FUNCTIONS
1.4  Security

■

Accessible station

The station accessible from the external device when a remote password is set for the CPU module and the station that can 
unlock/lock the remote password are limited to those in the same network number.
The following figure shows an example of when the remote password is set for multiple stations in the system.

Ex.

The A station can access the 

 station after the remote password for 1-1 station (1) is unlocked. The 

 station can be 

accessed if the communication line is open.
The B station can access the 

 station if the communication line is open.

The C station can access the 

 station after the remote password for 2-2 station (1) is unlocked. The 

 station can be 

accessed if the communication line is open.
The D station can access the 

 station after the remote password for 3-2 station (1) is unlocked. The 

 station can be 

accessed if the communication line is open.

: Station accessible from external device after remote password is unlocked

: Station accessible from external device even if remote password is not unlocked

: Station that cannot be accessed from external device

The password can be unlocked and locked by the following external devices.

• 1-1 station (1): A station only
• 2-2 station (1): C station only
• 3-2 station (1): D station only

External device
(Request 
source)

Target programmable controller (request destination)

1-1 station CPU

1-2 station CPU

2-1 station CPU

2-2 station CPU

3-1 station CPU

3-2 station CPU

A station

B station

C station

D station

RJ71GN11-T2

RJ71GN11-T2

RJ71GN11-T2

RJ71GN11-T2

RJ71GN11-T2

RJ71GN11-T2

RJ71GN11-T2

RJ71GN11-T2

(1)

(1)

(2)

(1)

(1)

(2)

(1)

(1)

Station C

Station D

Station A

Remote 

password

Remote 

password 

check

CPU 
module

CPU 
module

CPU 
module

Network No.1

Network No.2

Station 1-2

Station 1-1

Station 2-1

Station 3-1

Station 3-2

Engineering tool

CPU module

Remote 

password

Remote 

password 

check

CPU module

Network No.3

Remote 

password

Remote 

password 

check

CPU module

Station B

Station 2-2

Ethernet

Ethernet

Ethernet

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands