manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 90

88

1  FUNCTIONS
1.7  Safety Communications

■

Master station (safety station) and remote station (safety station)

The safety device status of the Safety CPU on the master station (safety station) is reflected to the safety output of the remote 
station (safety station). The safety input status of the remote station (safety station) is stored in the Safety CPU on the master 
station (safety station).

Setting method

Set safety communications in "Safety Communication Setting" under "Basic Settings". (

 Page 104 Safety Communication 

Setting)

Output from the master station (safety station)

 The safety device of the Safety CPU on the master station (safety station) turns on.

 The safety device status of the Safety CPU on the master station (safety station) is stored in the Safety output on the remote station (safety station) by safety 

data transfer.

 The safety output status of the remote station (safety station) is output to an external device.

Input from the remote station (safety station)

 The status of the external device is stored in the safety input of the remote station (safety station).

 The safety device status of the Safety input on the remote station (safety station) is stored in the Safety CPU on the master station (safety station) by safety 

data transfer.

END

END

Ò

Ó

Õ

Ö

Ô

No.0

No.1

Master station
(safety station)

Safety CPU

Safety device

Safety cycle 

Safety cycle 

Safety input

Safety output

External device

External device

SA\M0

SA\Y

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands