manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

The Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN is an advanced automation controller that ensures efficient and seamless communication within industrial systems. Unlock the full potential of this powerful device with our comprehensive user manual, available for free download from manualshive.com. Master this cutting-edge technology with ease.

Share
Download
background image

212

4  TROUBLESHOOTING
4.5  List of Error Codes

3135H

Over the number of stations that can be 
connected.

• Reduce the total number of stations to 31 stations (master station: 1, slave 

station: 30) or less.

• Reduce the number of CC-Link IE TSN Class B devices to eight or less for 

each port of the master station.

3136H

An illegal ring topology was detected.

Set a line topology or star topology, and turn off and on or reset all stations.

3160H

The number of points of link devices of the 
slave stations set to "CC-Link IE TSN Class 
A" in "CC-Link IE TSN Class" of "Network 
Configuration Settings" under "Basic 
Settings" exceeds the number of points that 
can be assigned.

In "Network Configuration Settings" under "Basic Settings", review the 
device assignment settings so that the number of points of link devices of 
the stations with detailed information 2 does not exceed the number of 
points assigned to stations with CC-Link IE TSN Class A.

■

Parameter 

information

• Parameter type
• I/O No.
• Parameter No.

■

Target station 

information

• Station number
• IP address

3180H

The set value is out of the range.

• Write again from the buffer memory, and reset the CPU module or turn the 

power off and on.

• If the same error occurs again even after writing again, the possible cause 

is a hardware failure of the error module. Please consult your local 
Mitsubishi representative.

3181H

• Parameter was not written correctly.
• Turned off during parameter writing.

• Write again from the buffer memory, and reset the CPU module or turn the 

power off and on.

• If the same error occurs again even after writing again, the possible cause 

is a hardware failure of the error module. Please consult your local 
Mitsubishi representative.

31ABH

It is not possible to guarantee the send/
receive of cyclic data of slave stations set to 
"Low-Speed" in "Communication Period 
Setting" within the "Low-Speed" cycle.

• Set "Low-Speed" of "Multiple Period Setting" in "Communication Period 

Setting" under "Basic Settings" to a value equal to or greater than the 
value displayed in 'Multiple cycle setting (low speed)' (Un\G1277442).

• Set "Communication Period Interval Setting" under "Basic Period Setting" 

to a value greater than or equal to the value displayed in 'Communication 
cycle interval (calculation value)' (Un\G1277443).

■

Parameter 

information

• Parameter type

■

31ACH

The settings of "CC-Link IE TSN Class" for 
the slave stations set in "Network 
Configuration Settings" do not match "CC-
Link IE TSN Class Setting" of "Connection 
Device Information" under "Basic Settings".

Set "CC-Link IE TSN Class" in "Network Configuration Settings" of the slave 
stations to "CC-Link IE TSN Class B". Alternatively, set "CC-Link IE TSN 
Class Setting" in "Connection Device Information" under "Basic Settings" to 
"Mixture of CC-Link IE TSN Class B/A or CC-Link IE TSN Class A Only".

■

Parameter 

information

• Parameter type

■

3600H

• For the inter-module synchronization cycle 

setting, the setting of the master station 
does not match the inter-module 
synchronization cycle setting of the local 
station.

• "Fixed Scan Interval Setting of Inter-

module Synchronization" of "Inter-module 
Synchronization Setting" in "System 
Parameter" does not match 
"Communication Period Interval Setting" 
under "Communication Period Setting" in 
"Basic Settings" of the module parameter.

• The values out of communication cycle 

setting range of the network module is set 
in "Fixed Scan Interval Setting of Inter-
module Synchronization" under "Inter-
module Synchronization Setting" in 
"System Parameter".

• Correct the parameter so that all modules performing inter-module 

synchronization have the same cycle setting.

• Check that the setting of "Fixed Scan Interval Setting" of "Inter-module 

Synchronization Setting" in "System Parameter" is consistent with the one 
of the communication cycle of the network module.

■

Parameter 

information

• Parameter type
• I/O No.
• Parameter No.

■

3601H

A mismatch occurs between the network 
synchronous communication setting in the 
network configuration settings of the master 
station and the inter-module synchronization 
target module selection of the local station.

Change the parameter so that the setting of "Select Inter-module 
Synchronization Target Module" under "Inter-module Synchronization 
Setting" is the same as the setting of "Network Synchronous 
Communication" under "Network Configuration Settings" in the "Basic 
Settings".

■

Parameter 

information

• Parameter type
• I/O No.
• Parameter No.

■

Error 
code

Error definition and causes

Action

Detailed 
information 1

Detailed 
information 2

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

EA SV Series Original Operating Manual preview
SV Series
Brand: EA Pages: 24
Taie FA Series Operation Manual preview
FA Series
Brand: Taie Pages: 66
Idesco EPC Manual preview
EPC
Brand: Idesco Pages: 11
B meters IWM-LR4 Quick User Manual preview
IWM-LR4
Brand: B meters Pages: 2
Baby Jogger City Single Assembly Instructions Manual preview
City Single
Brand: Baby Jogger Pages: 16
GAI-Tronics Elemec3 013-02-0095-002 Manual preview
Elemec3 013-02-0095-002
Brand: GAI-Tronics Pages: 12
Gardena EasyPlus Operator'S Manual preview
EasyPlus
Brand: Gardena Pages: 14
Gardena 1273 Operating Instructions preview
1273
Brand: Gardena Pages: 4
Gantner GAT ACCESS 6100 User Manual preview
GAT ACCESS 6100
Brand: Gantner Pages: 4
Harman AMX JPK-1300 Quick Start Manual preview
AMX JPK-1300
Brand: Harman Pages: 2
T-Link TL300 Quick Install Manual preview
TL300
Brand: T-Link Pages: 3
LLURIA LB-ART2 Manual preview
LB-ART2
Brand: LLURIA Pages: 2
tbs electronics Omnicharge Solar OCS 100-20 Installation Manual preview
Omnicharge Solar OCS 100-20
Brand: tbs electronics Pages: 64
Belden GRASS VALLEY MDX-3901 Manual To Installation And Operation preview
GRASS VALLEY MDX-3901
Brand: Belden Pages: 45
ADTRAN Total Access 351 Series Quick Start Manual preview
Total Access 351 Series
Brand: ADTRAN Pages: 4
YASKAWA PG-X2 Instructions Manual preview
PG-X2
Brand: YASKAWA Pages: 12
HANYOUNG NUX TPR-3N Instruction Manual preview
TPR-3N
Brand: HANYOUNG NUX Pages: 4
Black Stone BL 981411-0 Instruction Manual preview
BL 981411-0
Brand: Black Stone Pages: 2

Brands by name

Popular brands

Load more brands