background image

Overview

7. RS232 Pass-through:

9. Power on all attached devices:

2. Repeat steps 1 for the CTP-1301 TX/RX.

2. Repeat step 1 for the other side of the CTP-1301 TX/RX 

The JPK-1300 Jetpack 3x1 Switching, Transport, and Control solution

includes a 3-input wall-plate transmitter, a multi-function receiver, 

and a keypad for control. The purpose of this document is to illustrate 

how the solution is to be installed and set up in its simplest configuration 

by a trained technician.

The following items are included with the JPK-1300: 

• [1] JPK-1300 Wall-plate Transmitter (with Screws) 

• [1] JPK-1300 Keypad (with Screws) 

• [1] JPK-1300 Receiver

• [1] DC 24V 3.75A Power Adapter 

• [2] Power Cords (US&AU for UA version; EU&UK for EK version) 

• [1] Phoenix Connector (3.81mm, 2 Pins) 

• [4] Phoenix Connector (3.81mm, 3 Pins)

• [1] Phoenix Connector (5.08mm, 4 Pins)

• [1] IR Wideband Emitter Cable (1.5 meters)

• [2] Mounting Bracket (with Screws)

Active power requirements: 

• Voltage, DC (typical): 24V DC 3.75A 

• Power consumption (max): 80W (TX + RX + Keypad)

The environmental requirements for the JPK-1300 are as follows: 

• 

Operating Temperature:

 32° F (0° C) to 104° F (40° C) 

• 

Storage Temperature:

 -4° F (-20° C) to 140° F (60° C) 

• 

Operating Humidity: 

20% to 90% RH(non-condensing) 

• 

Storage Humidity: 

20% to 90% RH (non-condensing)

1. Position and install the mounting brackets of JPK-1300 RX with the

    4 mounting screws provided, as shown below.

2. Mount and secure the JPK-1300 to a surface or a suitable location 

    using appropriate mounting screws.

JPK-1300

 Jetpack 3x1 Switching, Transport, and Control Solution

AV FOR AN IT WORLD

®

QUICK START GUIDE

JPK-1300 RX

Installation and Connection

What’s in the Box?

Power

Environmental Requirements

Cable Requirements

1. CONTROL port connection distance is up to 164ft/50m via a Shielded 

    Cat 6/6A/7 cable. The CONTROL cable must be pre-run from the 

    Wall-plate Transmitter backbox to the Keypad backbox.

2. AV LINK port connection distance is up to 230ft/70m for 1080P video 

    or 131ft/40m for 4K video via a Shielded Cat 6/6A/7 cable. The AV 

    LINK cable must be pre-run from the Receiver installation location to 

    the Wall-plate Transmitter backbox.    

Install Jetpack Receiver

Connect Jetpack Receiver

1. Connect the pre-run AV LINK cable to the AV LINK port on the JPK-

    1300 RX.

2. Connect the power adapter provided to the JPK-1300 RX.

3. Connect HDMI OUT

    Connect an HDMI display device (such as a projector) to the HDMI 

    OUT port of the JPK-1300 RX.

4. Connect USB DEVICE

    Connect an USB device (such as a Smart Board) to the USB DEVICE  

    port of the JPK-1300 RX.

5. Connect MICROPHONE or OTHER ROOM AUDIO SOURCE

    Connect an audio source (such as a microphone) to the MIC/LINE 

    IN port of the JPK-1300 RX. (Make sure the MIC/LINE switch is turned 

    to MIC when connecting a microphone to the MIC/LINE IN port.) 

6. Connect AUDIO OUT

    Connect the AUDIO OUT port to an amplifier or powered speakers 

    and/or connect the AMP OUT port to 4/8 Ohm speakers using 

    appropriate speaker cables.

7. Connections for additional control options:

    • LAN control (Web UI/PC tool/Telnet/SSH): Connect JPK-1300 RX 

       to the same network of the PC or control system via the LAN.

    • RS-232/IR/RELAY control: Connect the RS-232 or IR OUT port of the 

       JPK-1300 RX to the display device such as a projector via an RS-232 

       cable or the IR emitter cable provided, and connect the RELAY 

       port (1-2) to the electric lifting projection screen.

    • Remote mute control: Connect the REMOTE MUTE port of the 

       JPK-1300 RX to the contact closure of the fire alarm system.

Note: 

Please refer to the Instruction manual for the configuration of 

          RS-232/IR/RELAY control and the REMOTE MUTE.

Connect Jetpack Devices

1. Connect one end of the pre-run CONTROL cable to the CONTROL 

    port on the JPK-1300 Wall-plate TX and the other end to the 

    CONTROL port on the JPK-1300 keypad.

2. Connect the free end of the pre-run AV LINK cable to the AV LINK 

    port on the JPK-1300 Wall-plate TX. 

USB-C

HDMI 1 HDMI 2

LINK

PWR

HDCP

SOURCE

USB-C IN

HDMI IN 1

HDMI IN 2

IR

USB HOST

JPK-1300-UA TX

VOLUME

DISPLAY

ON

DISPLAY

OFF

HDMI 1

HDMI 2

USB-C

ON/OFF

SYSTEM

JPK-1300-UA Keypad

To install the EK version JPK-1300 Wall-plate TX and Keypad:

1. Remove the white screws on the cover of the wall-plate TX and 

    keypad and remove the cover. 

2. Place the wall-plate TX and keypad into an EU standard back box, 

    and secure with the screws provided, as shown below. 

Note: 

Use the two screw holes on the left and right ends to install the  

          EK version wall-plate TX and keypad into UK standard back boxes. 

 

To install the UA version JPK-1300 Wall-plate TX and Keypad:

1. Place the wall-plate TX and keypad into US standard back box. 

2. Secure the wall-plate TX and keypad with the white screws provided, 

    as shown below.

3. Secure the cover back to the wall-plate TX and keypad with the 

    white screws provided, as shown below.    

USB-C IN

HDMI IN 2

PWR

USB-C

HDMI 1 HDMI 2

LINK HDCP

HDMI IN 1

SOURCE

IR

USB HOST

JPK-1300-EK TX

HDMI 2

VOLUME

DISPLAY

OFF

USB-C

HDMI 1

DISPLAY

ON

SYSTEM
ON/OFF

JPK-1300-EK Keypad

Installing Jetpack Wall-plate Transmitter and Keypad

USB-C IN

HDMI IN 2

PWR

USB-C

HDMI 1 HDMI 2

LINK HDCP

HDMI IN 1

SOURCE

IR

USB HOST

JPK-1300-EK TX

HDMI 2

VOLUME

DISPLAY

OFF

USB-C

HDMI 1

DISPLAY

ON

SYSTEM
ON/OFF

JPK-1300-EK Keypad

Connecting Jetpack TX to Source Equipment

1. Connect HDMI / USB-C IN

    Connect the HDMI and/or USB-C video sources to the HDMI IN 1, 2, 

    or USB-C port of the JPK-1300 TX.

2. Connect USB HOST

    If using an HDMI input, connect the USB HOST port on the JPK-1300 

    TX wall-plate to the USB port of the PC.

Reviews: