Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 126 | Manualshive

Page: 126 / 330

background image

124

2 PARAMETER SETTINGS
2.5 "CC-Link IE TSN Configuration" Window

Parameter processing of a slave station

The processing is to read and save the parameters from the slave station, and to write the saved parameters to the slave
station.
Also, it automatically sets parameters of the slave station from the master station. (



Page 91 Slave station parameter

automatic setting)

When performing parameter processing for the main module to which an extension module is connected, use
the following module.
• The RJ71GN11-T2 with a firmware version of "12" or later

[Navigation window]



[Parameter]



[Module Information]



Target module



[Basic Settings]



[Network

Configuration Settings]



[Detailed Setting]

Select and right-click the slave station, and select "Parameter of Slave Station" to display the "Parameter of Slave Station"
window.

«
...
124
125
126
127
128
...
»

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Brand: S&C Pages: 40

Brand: S&C Pages: 34

Brand: Haier Pages: 58

Brand: Samson Pages: 92

Brand: Jafar Pages: 10

Brand: Paratec Pages: 8

Brand: J+J Pages: 33

Brand: ZKTeco Pages: 2

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Barcelona Pages: 8

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: Gardner Denver Pages: 22

Brand: B&G Pages: 2

Brand: Lab.gruppen Pages: 2

Omnicharge Solar OCS 100-20

Brand: tbs electronics Pages: 64

Brand: National Instruments Pages: 17

Brand: Davey Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands