Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 84 | Manualshive

Page: 84 / 330

background image

82

1 FUNCTIONS
1.6 CC-Link IE TSN Network Synchronous Communication Function

Network synchronous communication with multiple cycles

When slave stations with different communication cycles (excluding local stations) coexists, cyclic transmission between
stations is performed according to the communication cycle. For the cyclic transmission of the master station and a remote
station, data can be transmitted to other stations after two cycles.
The following figure shows the cyclic transmission timing when "Communication Period Setting" in "Network Configuration
Settings" is set to "Normal-Speed".

• To perform network synchronous communication when multiple cycles coexist, set the setting of the local

station to "Basic Period" for "Communication Period Setting" in "Network Configuration Settings".

• When the communication cycle is low speed, synchronization is possible only when "



16" is set. Set "Low-

Speed" in "Communication Period Setting" under "Network Configuration Settings" to "



16".

(1) The communication cycle timing can be checked with 'Communication cycle timing' (Un\G1277440 to Un\G1277441) of the buffer memory. The timing of

data refreshed in the CPU module can also be checked with this buffer memory area. The 0th bit in this buffer memory area is turned on during the first (1/
4) cycle for normal speed. In addition, the 15th bit in this buffer memory area is turned on during the last (4/4) cycle for normal speed. (



Communication cycle timing)

OFF

OFF

OFF

ON

OFF

ON

OFF

ON

OFF

ON

ON

(1)

Inter-module
synchronization cycle

Inter-module synchronous
interrupt program

Operation
processing

CPU module

Network
module
(master station)

Output module
(normal speed)

System
of the
master
station

Input
refresh

Output
refresh

Inter-module
synchronization cycle

Inter-module synchronous
interrupt program

Operation
processing

Input
refresh

Output
refresh

Inter-module
synchronization cycle

Inter-module synchronous
interrupt program

Operation
processing

Input
refresh

Output
refresh

Inter-module
synchronization cycle

Inter-module synchronous
interrupt program

Operation
processing

Input
refresh

Output
refresh

Inter-module
synchronization cycle

Inter-module synchronous
interrupt program

Operation
processing

Input
refresh

Output
refresh

Inter-module
synchronization cycle

Inter-module synchronous
interrupt program

Operation
processing

Input
refresh

Output
refresh

Output refresh

Cyclic transmission

Output value setting

Cyclic transmission

Cyclic transmission

Cycle 4/4

Cycle 1/4

Cycle 2/4

Cycle 3/4

Cycle 4/4

Cycle 1/4

Normal speed

Normal speed

Normal speed

Un\G1277440.0

Un\G1277440.F

«
...
82
83
84
85
86
...
»

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Brand: S-COM Pages: 400

Brand: ZKTeco Pages: 8

Brand: EasyIO Pages: 18

DuetPro Carrycot

Brand: Qtus Pages: 52

CWDM-CR-B Series

Brand: Lantronix Pages: 19

Brand: Netafim Pages: 4

Brand: TREND Pages: 12

Pearldex Series

Brand: KaMo Pages: 2

Brand: AMX Pages: 1

ZoneSense Plus AS

Brand: Halma Pages: 58

Brand: Binder Pages: 147

Brand: Netro Pages: 14

Brand: Vent-Axia Pages: 4

Brand: Gliderol Pages: 2

Brand: Datel Pages: 10

Brand: Rasonic Pages: 14

ACCUVALVE AVC6000

Brand: Accutrol Pages: 74

Brand: Zapi Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands